Showing posts with label 3D Printing. Show all posts
Showing posts with label 3D Printing. Show all posts

Tuesday, September 22, 2026

If I'd known we were going to jam, I'd have brought my kazoo

 Gothsigh, grumble, and gripe: Operations stalled.  Kinda literally.

 I haven't messed with the printer for a few days because I am avoidant - like, it's a personality disorder, man.

 What I've been avoiding, until today (until some mysterious switch in my head got flipped the other way) is a filament jam in the extruder.  These were unheard-of with PLA, despite a really aggressive (non stock) tensioner and aftermarket... rims (had to say it) I mean extruder wheels.  I could make it quite tight to overcome resistance in the filament feed chain... like ferinstance when the reel is inside a dryer with stupid filament ports, outside the printer tent.  PLA tolerates a lot of squeezing and knurling.

 I switched over to some new TPU replacement (maybe, we'll see) which is a high flexibility PLA.  If you can see it coming now, why couldn't I see it coming then?

 Yup: I forgot to untension the extruder so while trying to load filament, the too-tight drive rolls squished the PLA-flex into funny shapes all around and near the bourdon tube and drive wheel, everywhere but into the tube.  100% my bad.  A right little mess.

 Unfortunately, with the printer inside the tent, it is a neck-craning pain in the, er, neck, to do anything to the extruder - even just adjusting the tensioner, never mind unjamming plastic bits from a tight mechanism and after five minutes of poking and proding with tweezers, dental probes, and a No. 11 X-Acto blade all to no avail, I walked away for a few days.

 There's always other stuff around this dump our majestic mansion that needs doing, after all.  Like all the things we should have done the first ten years we lived here, when we had money.  Cough, but I digress. 

 I really do not want to move the printer, I especially do not want to remove it from the tent unless I simply can't get this done any other way.

 Now it is time to dig into the extruder again (hopefully I can avoid disassembly) then see whether this flex PLA stuff can even be shoved through a bourdon tube at all, or if it requires a direct drive extruder.

 And where did my filament cleaners go? 😬

 I got the extruder wheel unjammed, still need to remove the bowdens full of filament and empty them.  Around then my leg started hurting again, so I'm not going downstairs to fool with the printer until it feels better.

 I'm also not working on shop projects, both for that reason and because my paint won't arrive until tomorrow, and because fucking Mouser canceled my order for bizarre reasons their abysmal customer service either could not or would not explain.  Meanwhile, they still show them in stock, but they won't sell me any.  I am so done with Mouser.  And why is an $11 relay now $30?!?

 ~≈{πŸ‘}≈~

Saturday, September 5, 2026

ABL - All 'Bout Leveling (3DP)

 This came up in the Creality Discord a while back, I've been meaning to mention it. problem: "I can't get my bed leveling system to work. I am using a Prusa style sensor with an Ender 3V2. (etc etc) " The Enders have glass beds. The Prusa sensors are inductive, which cannot detect a glass bed. Inductive sensors only interact with metals.
An inductive sensor will operate on an Ender, but you would need to change to a metal bed (ugh, why), or better, change to a capacitive sensor, which will detect any surface. It turns out that a mechanical switch like a microswitch, or an E/M sensor attached to a mechanical switch, has the best accuracy and repeatability of every sensor that multiple people have tested. Amazingly, in this at least, multiple testers' results all agreed. Except for the one fellow who built a horizontal test jig for stuff that works vertically against gravity (WTF OOPS) and sooprahz, sooprahz, sooprahz! All his results for the
mechanical sensors were worse than everybody else's... >_< But anyway. IOW, if you have a BL Touch or equivalent, you're good, you can probably stop thinking about bed leveling upgrades. ;)

Just as an aside, I have heard from some folks that were clearly unclear about how ABL works. This is understandable. It can be non-intuitive.

So, let's take my Ender 3V2 for example. It has a glass bed, but I have a mechanical 'BL Touch' type leveling sensor. Not only do we install a physical sensor on the hot end carriage, we must also install a firmware update to the little microSD card that runs the printer (in my case) because we are adding functionality to the machine which it did not have when it left the factory. How the install is done, the firmware used, etc, can vary from printer to printer, and it's off topic to try to explain several different ways, so I won't try.

Once the tech is installed, there is either a new menu or a menu item, in your printer's GUI. You use this to "scan" the bed at a selected number of points. Then the firmware moves about the bed, measuring the height of each point. This creates a new "mesh" which is simply a digital map of the bed's humps and valleys. You could just use this information to manually level the bed, and to a degree, I do this, just to get the bed to within spitting distance of level.

But that is not where the beauty of ABL lies.

Because the mesh is also used by the firmware while printing; it moves the head (or bed, depending on printer - in the Z axis anyhow) up and down as it prints, to follow the real contours of the bed as it is, leveled or not! This is dynamic virtual leveling, it is bad-ass, and you want it.

Even if your bed is so messed up it will never be level, ABL will make that problem go away. Scanning for a new mesh if fully automated, just click on a menu item, it takes only a few minutes, and you should only need to do this when you have moved or bumped your printer, cleaned the bed vigorously, etc. You won't be doing it all the time.

This action is faded out as the print continues and for most prints, it can be faded out completely after 10 or 20 layers. That's usually a simple setting in the printer's control panel, under the ABL menu item. That's how the obviously-distorted first few layers transition to normal, straight, printing. The first few layers may be distorted slightly (in the Z axis) but because they follow the bed's real contours perfectly, first layer adhesion is vastly improved, and that's really what this is all about. Keep spaghetti on the dinner table where it belongs!

So, a bed could be really messed up, to the extent that you couldn't even print on it without ABL, yet with ABL, it will print, and it will print just fine. There are demos of this on YouTube. My own Ender 3V2 has a leveling screw at each corner, but the ABL mesh reveals that no matter how much manual leveling I try, in an effort to get the four corners and center to more-or-less agree, and it's not quite possible.

ABL permits you to have a perfect virtual bed, even if the real bed is not perfect.

Out of all the upgrades and tweaks I've made to my humble bed-slinger, ABL has been the best bargain. 

 ~≈{πŸ‘}≈~

Tuesday, January 27, 2026

everything is fine here, no problems at all, how about you?

 Back is better, heart* much worse.  Desperately seeking distractions / diversions.

Trying to find a filament dryer that meets my needs but doesn't require taking out a second mortgage.
Drowning in analysis paralysis.

requirements
• usable while printing, so no nonsense about cardboard boxes sitting on the printer's bed
• MUST reach a minimum of 80ΒΊC so I can dry high temp, hygroscopic materials like PA6
• front filament exit because the dryer will sit on a shelf above my printer bench†
• "affordable" meaning $50/spool capacity, or less
• spaces for desiccant packs, hopefully I can use my existing DIY
• prefer higher wattage (ie; north of 200w) so it doesn't take half a day to reach temperature
• no food dehydrators; too much work to give those the usability features I want
• an accurate hygrometer would be cool, but nobody seems to be offering that
• I probably need two spools capacity, minimum

This is just idle chit-chat.  I'm not ready to buy one right now, and I don't mean to use my readers as a search engine.

Heh; in theory, I could put the above into some AI tool or other and see what it spits out, but I dislike and distrust AI tools.  What few experiences I've had, have not been useful/helpful, just aggravating, so I mostly refuse to touch AI.  I try to find YT videos that are not obvious shills / Amazon affiliates, but those are few and far between. 

Hmm, there's a thought: I should dump my YT bookmarks here, seriously. 
No AI slop, all quality, many topics.  Curated too; recently removed a semi-popular "former physicist" after realizing she just isn't a very good scientist. ;) Just need to figure out how to dump the list 'cuz IIRC, YT doesn't provide one.  I'll poke around.  There's far too many to transcribe manually. O_O

And that's enough onion-belting†† for now. ;)

~≈{πŸ‘}≈~

______________________________________________
* figurative, not literal; my cardiac health is just fine

† I'd really prefer that exit to be a push-in fitting for a bourdon tube; most are now anyway

†† telling long-winded, rambling stories, like the time I caught the ferry to Shelbyville. I needed a new heel for m'shoe. So I decided to go to Morganville, which is what they called Shelbyville in those days. So I tied an onion to my belt, which was the style at the time. Now, to take the ferry cost a nickel, and in those days, nickels had pictures of bumblebees on 'em. "Gimme five bees for a quarter," you'd say. Now where were we... oh yeah. The important thing was that I had an onion on my belt, which was the style at the time. I didn't have any white onions, because of the war. The only thing you could get was those big yellow ones. (Simpsons)

Friday, January 9, 2026

Always Change As Many Variables At One Time As Possible

 Mmm, yes, that's a good idea! >_>

 Depending on what my back lets me do, I might replace the Y-axis belt tensioner today.
[later: nope, cry, hurts]

 Once that is done (meaning, belt re-tensioned using both calculated audio & belt tuning app and investigating if they don't match)...

 I plan to try a print with:

• Flexible PLA
• a 0.8mm nozzle
• a 0.3mm - 0.6mm layer height {to be reviewed; I want thin, flat, slow layers}

- all for the first time of course.  <_<

[later: ah-heh, maybe another week. Owwww.]

 I think the reason I am like this is that life has always thrown me into the deep end of everything, all the time, so I'm just used to it.

~≈{πŸ‘}≈~

Saturday, January 3, 2026

grumpy old man doesn't understand world he lives in, "film at eleven"

 So I bought a replacement Y-axis belt tensioner.  It is made of aluminum and weighs sixty grams.  I don't think the extra mass - presumed extra mass, I gotta take the old one off to weigh it - will be sufficient to cause problems.

 It hasn't been installed yet because of ongoing severe back pain which has kept me immobilized for several days.  For under ten smackeroos I couldn't be arsed to make it from scratch.

 In the mean time, I've been shopping around for filament dryers since the filament I've had sitting around for five years is now showing signs of humidity absorption, and I was hoping that post-holiday prices would drop.

 I had half-settled on one, and even had it in my Amazon wish list, but then the price bounced up and I decided to see if it was just that vendor or everybody.  It was just that vendor, so all well and good, but then I found the ringers which really prompted this post.

 So the unit I'm looking at typically sells for ≈ $160 US.  You can get it as low as $102 direct from Aliexpress, or a bit higher if you choose Amazon.

 But two vendors want more.  Much more!  One eBay seller wants $700+ and another $900+.  I thought maybe they were selling four or five units, or throwing in a free printer, but they are not.

 It's not the first time I've seen this.  Can anyone explain what's going on?  The high flyers are usually on eBay, not always.  Shoppers are not stupid, they aren't going to buy that when the same unit normally sells for 1/4 of that.  Unless it's a money laundering scheme?  My dumb ass is not very good at thinking up successful criminal enterprises, or I'd be a lot wealthier.  IDGI.

~≈{πŸ‘}≈~ 

 

Monday, December 29, 2025

because life would be boring without a few setbacks... now and then... right?

Uh, is that a crack? It looks like a crack.

 I do not believe this belt tensioner is supposed to be at an angle with respect to the rest of the arm:





um, those are new since yesterday
Uh-oh, that doesn't look right!

 If only I had some device, machine, or tool that can make complex plastic parts easily... d'oh!

 The best part is, I ran another test print without realizing this was busted, and the print completed.  Was run at 125% speed too, just for yucks.  I'm not saying it was pretty... O_O

 I can probably buy another one or someone's claimed unbreakable upgrade (which will be glass-  or carbon-filled, but printed, and therefore quite breakable) or I could machine one from aluminum.  I guess there's other materials I could use, but out of everything I have on hand, aluminum seems like the best choice.

 The next issue is that aluminum is heavier than whatever unfilled garbage resin Creality™ used for this part.  It's a stressed part; why was it not glass-filled nylon?  And that matters because of how this printer's Z axis works; from one end only.  The design works best if the wheels never wear at all, and the far end weighs nothing at all.  Um... <_<

 I was so naive, thinking I was nearly ready - with just some tuning and probably a bunch of filament-drying - to start printing for real.  Silly old man.  Silly, SILLY old man.

PS: machine has not been moved in years.  Belt was not over-tightened.  Well now, it's probably a tad under-tightened.  I'm frelling grumpy about this, TBH.  I think I need a break again, I feel like I'm constantly being sabotaged by invisible fairies and ninjas.  Ninja fairies, even!

UPDATE: I ordered a metal upgrade unit.  For $11, I couldn't be arsed to make one.

 This also leaves me with a spare bearing and pulley for what should be a high-wear area... if I were printing a lot. 

The blue knob is trash.  I have enough bakelite knobs, I certainly don't need any crappy PVC knobs.

 Belt tensioning is done sonically with a belt-tensioning phone app (easiest) or by calculation and any free audio measurement app.

~≈{πŸ‘}≈~

Wednesday, December 17, 2025

now let's talk about print quality... *sigh* the number one bugaboo of 3D printing

 "PRINT QUALITY"?? 
Hey isn't that where we left off eighteen months ago? 
(yeah, pretty much, before the upgrades and modifications, the extended cable
drama, the broken camera ribbon cable socket, the camera noise problem,
printer firmware updoot, controller updoot...)

Ahem.  Finally we return to working on the printer's actual purpose, printing.  I was pretty proud of the big owl I printed a year or two ago until I noticed the overhang problems.  Granted, printing overhangs without a support is a recipe for trouble, and I was using a comparitively primitive Cura Utilimaker to slice then.  I am now using PrusaSlicer, and if I do it again, there will be a mess of supports, probably.  The whole breast of the owl?  Couldn't we uh, just make it print overhangs somehow?  Mostly no, AFAIK, but a lot has happened in the last eighteen months, and gho knows what new cleverness has been released since then.  edit, later: I think the solution for that owl is to print it upside down.  I'm serious.

 Amusingly, as soon as I loaded good old Benchy into Prusa, it complained about the model, saying it might not be stable, there might not be sufficient bed adhesion, I should consider supports and a brim. 

Well, Benchy isn't supposed to be easy to print beautifully, it is supposed to be hard to print beautifully.  That's why and how it is a benchmark.  I also use CHEPs cube and anything else someone can show has merit.  The thing about Benchy is that everyone uses it and there's a lot of information about it, charts featuring it, etc.  Great for the beginner like me.

 But as for the low bed adhesion warning (which it bases on the base minimum width vs. the model's maximumn height) well, I could be a spokesmodel (can you see me in a bikini? Egad, best not.) for that Layerneer bed glue. It's a routine part of my flow now.  Granted, sometimes I just re-wet the existing and smear it around again.

 I think it is an Amazon stealth brand, TBH.  Got bed adhesion problems?  Stop!   Before you start messing with rafts, brims, and supports, and assuming you have a sane bed temperature profile, try somebody's, anybody's bed adhesive.

 I only have experience with this Layerneer stuff, which came to me as part of an Amazon starter package (I swear to Ghu, it was the exact thing I needed, in that moment).  Maybe I'd use it up faster if I printed more (I took more than a year off, whaddya want)  Since I began using it, I've only had a model break loose once, and that was because it was a max-volum model with many supports, and when the bed was allowed to cool off as "normal", the model broke loose.  A solution I haven't tried yet (because the print quality was ass too) is to leave the bed hot for the whole print.  Next time.

 

 Here's a test print I did with a small kodama ornament; you can see it's got serious issues.

 The tiny blebs are mostly due to the filament having sat unused and forgotten, on the printer, inside the tent... for the last eighteen months.  πŸ’¦

 The only reason this prints at all is that the tent was closed up and it has a lot of silica gel socks lying around the bottom of it.  This is why filament dryers are useful, and why good dry storage is mandatory.



 Aside from the blebs, you can see that the first layer -  in fact all the layers - look a little bit high, and should be smooshed flat against the bed just a little more (for good bed adhesion).

 A taller layer height also makes for more pronounced layers and a less-smooth print.  Okay, so layer height needs to be tweaked in the slicer, right?  Ah, but reducing layer height strongly increases the number of layers and thus the print time. 

 I'll worry about that stuff when I'm satisfied with the bed leveling, which is taking me some time because I am being anal about it, and because there is no screw in the center of the bed and it seems as if there needs to be one. >_<

 And an afterthought: I've got some soft PLA I haven't tried.  It's yuge, as in 1.75mm, and I haven't any nozzles big enough - maybe.  Some say a standard 0.4mm can be used but most do not recommend the usual, saying 0.6mm is the absolute minimum. 

 The fancy "splitter" nozzles (see right) look like a good idea for such large filament because thick filament is harder to heat through if the filament is moving fast - plastics are lousy conductors of heat.  So Bondtech CHT and imitators have a design that splits the incoming cold filament into three separate channels, significantly increasing surface area, and reducing the "heat-through" cross section greatly.

 Unfortunately I'm not feeling generous right now and they want too much coin for just one nozzle.  There are "clones" but most I've looked into seem like very bad fakes, not clones.

 In fact, I'm thinking of drilling out a spare nozzle and trying it... getting the nozzle smooth around the hole >_> might be tricky.  Not sure how I'd drill it either, given that the lathe is currently in several pieces.

"I see no purple light crashing out of you (so just walk on in!)" -- The Sisters of Mercy

 Notice anything different?



 It turned out as I suspected: there was one crucial place in the complex chain which, if I choked it, would block most of the noice from entering either the camera or the camera port in the Pi.  This is a lot easier to apply than adding components inside the TCS, but that still needs to happen since it is the source of the problem.

 But in the mean time, I got lucky: one common-mode choke (mystery ferrite, probably mix 31 based on how well it works) with two turns on the core.  I'd have done three but I couldn't get the connector through again.


 EDIT LATER: when I posted this, there was supposed to be a video clip showing the printer running via the R-pi cam, but without the purple flashes.  So here is that:


 This outcome confirms my suspicion that the EMI was A) conducted not radiated and B) common-mode in nature.  And those suspicions were just based on experience, I'm afraid.  I am startled to have found a critical spot on the first try.  Back when I was getting paid to do EMI suppression for "EMC Acceptance Testing" it was rarely this simple to solve a noise problem, I can assure you!  (fortunately, I had very smart and experienced help)

 At some point, I will install both common and differential mode filters, plus small capacitances (handwave let's say at the relay and at the outlet (forming a pi network I guess).

 One has to be careful specifying and selecting such caps to be used across the power line, especially if they're expected to survive surges and spikes...

 On a 120VAC circuit, a capacitor with a 300VAC rating would be a minimum for the supply voltage alone, and normal best practices suggest 600VAC rating.  From my own reading and experience, and given that there are no other transient voltage surge suppression devices in this box, these devices should be able to survive a 3kV spike if you're being lazy, and a 6kV spike if not.  Good thing these are very small value (.001uF/1000pF should do it, and the reactance is so low their current draw may be ignored) capacitors.  Some likely suspects are the self-healing metalized plastic units on DigiKey rated for 6kVDC, whose longest dimension is 1.2in - they should do nicely.  The ferrites will be somewhat larger.


Friday, December 12, 2025

the bizarre camera problem

<this is not a Moving Picture>

 So I've traced the camera problem to my temperature control system.  If I turn it off, the problem goes away.  This is not unreasonable for a suspect, as SSR switching is notoriously fast and therefore nasty.

 Neither the R-Pi nor the printer is connected to the temp control system in any way, so this could be either radiated crap or coming in to the devices via the common power strip.  Okay, but why the hell does the connection between R-Pi and printer matter??   o_0

 I've honestly considered that the aluminum coating on the inside of the printer tent could be acting like an antenna or at least a big capacitanc, coupling between the wires for the printer and Pi, and the wires for the temp control fan and heater.  Hmph.

 What I want to do for a solution is to find an unused Tripp-Lite™ Isobar™ unit and plug the temp control system into one channel and the printer and Pi into the other...

 But since I'm fairly certain all of mine are in use (uh, I could give up the stereo?  or um... yeah, not) and even used ones are not really in my budget, (what budget?) the probably-optimum solution might have to wait.

 The next thing to try is to get a bunch of 77-ish split ferrites or a couple of big toroids I can loop power cords through.  If that doesn't work, I'll look for a used 3-channel Iso-bar unit and plug the three offending items into that rather than all together on the same outlet strip as everything else.

 I'm also going to consider installing shielded & grounded cable between controller and heating element, since that is the thing which is constantly getting switched on and off.  The wire gauge can be tiny because 120V and small wattage.  Existing wire is twisted a lot, but apparently that's not enough to stop.  The might be a common mode thing or radiate RFI.

 PID + PWM is really good for controlling an SSR and heating element, but unless it is zero-crossing switched - and this one apparently is not - they are kinda notorious for generating noise.  I had problems with this professionally maybe a hundred years ago with process controllers that drove SSRs, but I plumb forgot about that until now.

 I wonder whether I could get away with putting say, a 0.01Β΅F capacitor directly across the load terminals of the (fake, chinesium) SSR I used.  Might it destabilize the thing somehow? It would help take the edge off (geddit) the switching transitions.  I gotta find the manual and see if there is a way to make the controller switch on zero crossing or not.  Problem is, I don't really keep any parts of any sort on hand any more.  There are some odds and ends lying about, but they are rarely useful.  And a former housemate stole a few things from me which I didn't catch until much later.

 Today I also swapped out the disastrous tangle of a very weird old EIA outlet strip for a normal one, much longer, without the outlet cables/splitters involved with the old one. O_O

 This is not terrible progress given I am also working on other things today, like the plumbing disaster in the shop toilet and a spot of house cleaning.  Since the Ritalin apparently stopped working nearly a decade ago (how is that even possible?) I am completely scatter-brained most days, trying to do too many things at once.

3D printing under water...

 When I first got my printer set up and tweaked for a roll of inexpensive (Amazon Basics, LOL) PLA, I was pretty darned impressed with the print quality.  It had taken some fiddling, but once it was working, wow!  It just worked!  Hardly any stringing (er, well, after I learned about and made more adjustments in the slicer) and hardly any cleanup work post-print.  I was so stoked.

 But then I didn't mess with it for a while, and when I did, even though no settings had changed, even tho I let it warm up a-plenty... the exact same prints - an owl or a Benchy - looked like ASS.

 That was when I learned that all filaments are hygroscopic.  What had changed was that we were now in summer months, and the evap cooler was running, with the coolest, densest, dampest air settling in the basement where the printer is.  The consequences of "wet" filament are worse for some materials than for others.  Although good old PLA is highly hygroscopic, it is probably the least sensitive to humidity in terms of effects on the printing.  On the other hand, PLA is one of the easiest to dry out, and doesn't require a high temp or long time soak to do so.


 It was around then I bought a tent (or a friend did; I can't remember who bought which accessory 'cuz right after one dear friend GAVE me a brand new E3V2 as a gift, another dear friend bought me a ton of accessories) -- then I built a circulation fan and tube, and a temperature control box with a PID controller in it.  Inside the tent are several "socks" (piece of wife's old pantyhose) filled with silca gel.  The controller build is documented in this post.

 The tent keeps already-dry filament from getting "wet" but it's not hot enough to dehydrate wet filament, unfortunately.  If it were, the electronics of the printer would COOK, killing the printer.

 For storage, I've just been keeping unopened reels in their bags, but I've recently learned that over enough time, water vapor can penetrate most of those bags too.  Opened reels I've just been resealing with clips and with another small silica gel sock in each bag.

 Unfortunately, it now appears I need a filament dryer.  Of course the first thing I thought of was making my own, but when I looked at the cost of parts and my own time, I'd be spending more money than even a deluxe commercial unit costs.  Which frustrates me because either way it is far more money than I want to spend.  Maybe the prices will drop enough after the holidays. πŸ˜’

------------------------------------------------------------------------------------------------

                     Dryer               Drying
Filament     Temperature     Time (Hours)  

PLA            55°C (131°F)     > 3  
ABS            65°C (149°F)     > 3  
PETG          65°C (149°F)     > 3  
 Nylon          75°C (167°F)     > 12  
 Desiccants   65°C (149°F)     > 3   
 PVA             45°C (113°F)     > 10  
TPU/TPE     55°C (131°F)     > 4  
ASA             65°C (149°F)     > 4  
PP                55°C (131°F)     > 6  
HIPS           65°C (149°F)     > 4   
PC              75°C (167°F)     > 6
PEEK          75°C (167°F)    > 6
 
These recommendations are made under the following conditions.:

    • ambient humidity: 50% RH
    • 
ambient temp: 25°C
    • for a single 500g filament spool


= trying to make any kind of coherent chart in Blogger is nightmarish =

----------------------------------------------------------------------------------------------

 Now, there are compromise solutions, but they don't work very well for me.

 One way to dry a roll of filament is to put it on top of some non-heat-conductive spacers (so the reel isn't in direct contact with the bed) on top of your printer's print bed, then enclose the reel with a spare cardboard reel box, then adjust bed to correct drying temp, set a timer on your phone or a kitchen timer, et voila!

 Of course, then you can't use the printer... >_<

 Another solution is to buy a food dehydrator cheap, if you can find one on sale or the thrift store, then 3D print a support spider for the reel (uses three ball bearings, works like the one in your microwave oven), and 3D print a housing to keep the hot air in - the trays that come with the dehydratopr are not worth the trouble to try to make a side wall housing out of.  This seems... okay-ish, to me, but I'm not wild about it. It does have the advantage (most food dehydrators do anyway) of reaching 85C for drying out the more "engineering" filaments.

 Now I had originally had the notion of making a filament dry box to keep filament dry while in use, it's easy and cheap to make one from a clear plastic storage tub... but that won't dry out filament that has gotten "wet".  And if I have a dryer, they're already set up to be used while they dry anyway, so I wouldn't need the separate dry box... but I do need a dryer of some kind... grump.

 This is why I am now pondering this perfect - and expensive - four reel / two oven filament dryer:


 The Creality Space Pi X4 has two ovens with independent temperature and timer controls, enabling two different filament types to be dryed at once, and all four reels can be in use if you have four printers or an Automatic Filament Changer. 

 The latter is something I might tackle some day - there are DIY print-your-own / build-your-own files on the 3D model sites, there are unassembled kits with all the parts bought for you, and of course there are ready to use commercial ones.

 So long as you're slicing with Prusa, the use of an AFC should be fairly slick, automatic, and without manual intervention.  You declare the colors of the various parts of the model in the slicer and it takes care of the details.  (hah!  there is always some fiddling to get set up)

 So once it's dialed in, color changes mid-print with a single-filament cheap printer like my Ender3 (or any other bed-slinger you might have) suddenly become trivial.  No need to drop three thousand simoleons to have a multicolor printer!

 Another criteria that narrowed my choices a lot is the need to dehydrate high-temp and high-density filaments like nylons and PEEK.  I already have some, and I intend to get others like PC, so a dryer has to be capable of max (about 85ΒΊC should be the highest you ever need) drying temperatures.

 aside: I am finding that 3D printing strongly resembles 1970s
hot rodding, in that you really can unbolt one part and then
bolt on another that adds performance, before you even take
apart an engine - new intake manifold, big carb, carb temp
spacer, turbo or maybe a Paxton blower, exhaust headers,
spicier ignition unit, higher flow fuel pump, and so on.

  But unlike a chrome air cleaner or vortex inducers, most of the 3D printing hacks actually do improve your printing, ie; they are not snake oil. :)  And it's FUN.

Thursday, December 11, 2025

My OctoPi (Raspberry Pi Cam) has purple hiccups

 

That, friends and neighbors, is what happens when my camera is working, but the R-pi is also plugged into my Ender 3V2... as it sorta tends to be if you want the one to control the other...

 Note the emphasis on 'my'.  Apparently other people are not having this problem.  Those that do, solve it by installing a ground / power isolater in the USB port, to prevent power supplies fighting or noise.  Sounds good, doesn't work.  This video was made with said device installed.  I also took one apart (I have several) and tried isolating the power ground not just the 5V line, same result.  Since I bought several, I've considered building little filter networks into one of them, but I don't think this is high frequency hash.  Bigger guns are required.

Just unplug the printer and the camera view becomes clean and noise free. Well that might be okay if all I wanted the R-pi to do was stream video of the print...but of course I want to control the printer with OctoPi/OctoPrint.

 My next instinct would to install some common mode noise rejection in the form of a whacking great ferrite, but said ferrite is MIA.  I need some really big Mix 75/77 clip-on ferrites.  Clipons seem hard to find in the low-frequency mixes.  Poop.

 Anybody got an old CRT sweep ferrite core mostly intact? That will work handily, just zip-tie the two halves together firmly and pass the cord through it two or three times.  Well I haven't seen one of those in fifty years. ;D

 This problem is annoying me because interference works both ways... I'd prefer not to throw glitches into the printer either.  So this has to get fixed before I will attempt to restart printing (mainly, profiling some filaments I haven't used before, starting a filament notebook or spreadsheet for filament settings, etc).  I have an old PowerBook with a bad battery which I keep on the printing bench for such utilitarian purposes, checking the camera stream, etc.

 I'm also sorta pondering how to make the R-pi camera video publically available without compromising my network.  In general, I do not poke holes in my firewall at all.  We'll see. That's a low priority.  In the past (before the upgrades, LOL) it was very useful to be able to check a print's progress remotely.  On one occasion while I was at work, I checked on, and stopped a print which had come loose from the bed and was doing the Bird's Nest Dance.  (solution: Layerneer Bed Weld, man, we lurves it)

Monday, December 8, 2025

(3D Printing) Never have I ever been this happy to be this wrong

 I've been sorta avoiding working on my 3D Printing setup because I was under the impression I had a lot of annoying, fiddly problems to solve, to put it back in working order after multiple upgrades, a mis-aligned extendo ribbon cable between control panel and printer (sorta necessary when printer is in a tent), and some other issues.

 Today I decided it was time to dig in and get it done.  I'm doing laundry anyway (which is in the same room) so I figured I could hang out down there fiddling with the printer while I'm waiting for laundry changes.

printer & panel work and
the new graphics are dope
  [Blogger wouldn't let me align these photos no matter what I tried - WTH?]

auto-leveler works
enclosure temp control works


The R-Ο€ works fine too, I just got sick of wrestling with images and Blogger.

  Ahem.  Well.  It turns out I fixed all of the most-worrying problems some time ago and forgot that I had done so.  I powered up the bench and everything came on and seemed to be working fine.

  Now I merely need to:
• find or fix a working keyboard to connect to the Raspberry-Pi
• twiddle a few system settings that must be changed to accomodate the new higher-wattage heater
• update Python on the R-Ο€ (just found this out, you have to burn a new Β΅SD boot card, sigh)
...then I can start running test prints.
• install a new power outlet strip

 I might have to re-level the bed if the printer has lost those settings.  Auto bed leveling accessories are the bomb.  Do 25 points and go grab a cuppa. :)  The 3D heat map of the actual bed height/shape is really cool, and for me at least, it really helps me to understand what I need to do.

 I could wish the controller was a touch pad instead of the stock I/O knob, but that's for another time far in the future after everything else has been addressed.  Especially since I can't hardly afford the accessories and upgrades I need now, so luxury tweaks can certainly wait.

 I also have a very nice outlet strip for the printer bench I need to install some day soon.  I seem to have a lot of things on that bench which plug into AC, and the cord pile behind that bench is a dog's breakfast.

 And the R-Ο€ needs to be relocated off the top of the tent, which is more about re-routing cables.  I can't stand having a work area that is constantly untidy and covered in loose cables.  Besdies, with my tendency to twitch or fumble these days, it's a recipe for disaster.

 Granted, since I have now changed the extruder, the hotend, the coldend, and probably the lukewarm end, there will be several settings that need changing.  I have to re-learn a lot that I forgot most of a year ago, because I've been "just getting started" this whole time, and there hasn't been enough repetition to make the fiddly details stick.

 I hope I can get to where all the filament settings are set in the slicer and downloaded to the printer with the job, in a way that's easy and smooth to change for each filament and model, with jobs submitted and monitored remotely from my main desktop (upstairs) using the R-Ο€.  I hear slicers have gotten better since I last looked.

 Anyway, that's the plan.  And either buy or build some kind of filament enclosure for the spool that is currently in use, because extra spools definitely don't fit inside the tent anywhere, and the tent will never be hot enough to dehydrate anyway.

 A friend bought me several kinds of spool rollers and -holders, and I've no way to put them to use yet.  I don't especially want to build that enclosure, but we're broke and they seem kinda spendy considering the inexpensive mass produced plastic moldings they are all assembled from.

 Oh, if I recall correctly, there was trouble with the Pi-Cam, so I may need a new one, or perhaps just another cable.  Or it could be working fine, but I have to reconfigure the R-Ο€ and probably update OctoPrint as well.  And ahem: whoever decided that delicate ribbon cable was the way to make that camera connection was a bonehead.

 Of course, as any other 3D printing enthusiast could tell you,
this entire exercise is only so I can justify buying more kinds and colors of filament...
;)

Tuesday, March 7, 2023

temperature control system for 3D printer enclosure

 The Problem:

 My 3D printer is in a basement room which, in the winter months, stays well below reasonable printing temperatures. The house is literally 115 years old, so fixing the room temp isn't going to happen.

 The First Half of the Solution:

 Fortunately, a very good friend gave me a heat-resistant 3DP enclosure.  The printer alone dissipates over two hundred watts between the bed heat, hotend, and motor drivers.  So I measured temps after the printer had been in "preheat" mode for 30min, and it plateaued just below where I needed to be, while the room temp was on the "high" side of its low range.  Well poop. 

 My tent needed a heater, but obviously if I just stuck a small heater in there, there would be nothing to stop the temperature from climbing so high it cooked the printer's electronics.  It was time to consider a proper temperature control.

 The first bit of good news is that I've done this sort of thing before so I already knew how easy it really is.  It's just a matter of buying a few Commercial Off The Shelf parts and connecting them together with a few simple screw terminal connections.  Usually, you don't even need to solder.

Complete kits containing the PID controller, a "solid state relay", and a heat sink can be found online for under $30, so I did that because I was broke and cost had to trump quality this time.

  (for the reason 'SSR' is in quotes, please see this Big Clive video, in which he tears down an identical unit)

 So it's a fake SSR in the strictest sense, a sense we don't care too much about, but the screw holding the thermopad / TO220 style device inside to the back plate was literally sticking out of the heat sink surface! I had to file and sand all of that flat to get a good mate to the all-too-thin Chinesium heat sink.

 Fortunately, the thing has astonishingly low forward drop compared to the devices I am used to; it didn't get warm at all under a 20A load, and the device is nominally rated to 40A.  I flatly did not believe that number before I tested it... but it might be possible!  In any case, the load for this application is only 2.5 amps.

Visions of Rosy The Riveter, hashtag 'we can do this'.
 The next item I needed was an enclosure.  Because I needed to preserve as much desktop real estate as I could, I decided I wanted a deep enclosure with a small front panel.  After poking around the usual places, I was astonished to find that I couldn't find one to buy at any price, so I decided to make one.

 A quick review of available materials and a bit of brainstorming assisted by a bowl of the finest Longbottom Weed, I realized that a scrap of extrusion which has been knocking around my shop for literally decades had finally found its true purpose. All I had to do was cut it in half, patch up a bunch of ugly holes, mill a bunch of not-ugly ventilation slots, oh and figure out how to attach the two cut halves to each other in a permanent and durable way, without being able to weld aluminum.  No problem.


 This we then do.

 

  I drilled matching holes in the thicker bits where the two halves would meet, epoxied little aluminum pins into the holes, applied epoxy to the roughened edges, and "glued" the two halves together. 

 When done, I lacked confidence in those pins and their small surface areas, so I added three machined 'clips' and epoxied those to the inside, around the thick edges.  NOW I am semi-confident that the two pieces will remain one piece... provided nobody drops it.  I wish I had thought to take a picture of them before I painted everything black but I didn't so there it is.

 Next I needed a front panel for the controller and a power switch, and a back panel for power entry module, fan and heater output receptacles, and thermocouple input terminals.  That effort looked like this:

Blogger won't let me put multiple photographs on the same line, isn't that amazing?

 The back panel was a bigger PITA than the front, because it had more fiddly holes in it, but nobody sees it.  

 The front panel needs to look good, but it's only got two big square holes and the four small panel mounting holes.

 I have to assume this extrusion was intended for making things like this.

I also have to assume there is clever hardware for joining the halves which I do not have on hand.

 I decided to make the front panel unnecessarily thick, so I could unnecessarily counterbore the panel screws and use socket-head cap screws for added sexiness.

 This is why some of my simple projects take a long time, but I was motivated to do a better job than I usually would (for myself) because I planned to blog about it here, and I didn't want to embarrass myself.

Fiddly, fiddly. Measure thrice, cut once.

 At least with the front and back panels, if I scrapped one, I could replace it.  That wasn't true for the enclosure halves, and I was tense about that a few times when I was cutting on them.

 


Milling thin materials - or rather, fixturing thin materials so you aren't also milling your machine's table... can be interesting.

 I saw no reason to put much effort into the finish of the back panel, so I just ran it over a convolute wheel on the buffer a few times.

 Then came paint.  On a lark, I decided to coat the enclosure with Rustoleum™ Texture paint (rattle-can).  I bought it with my employee discount at the store where I work.  This won't be an endorsement, nor a condemnation, because while I like the finish, Rustoleum seems to have a problem with their cans; since they now spray in any orientation, it's not possible to clear the nozzle & valve per the instructions still printed on the can.  

 As a consequence, you can get two, maybe three spraying sessions out of a can before the valve clogs.


"image enlarged to show texture"
( for scale, that's a countersunk hole for a #10 screw )

 Seriously, this stuff has a lovely appearance and feel, at least for my aesthetics.  The feel / texture is not "rough" in that it does not drag against the skin the way, say, sandpaper might, as the peaks are not sharp, but it is noticeable.

 The character of the texture changes somewhat with additional coats.  I did a few tests on other bits of aluminum, and it adheres under abuse, and once baked on with heat (always do this if you can) it becomes quite scratch and abuse-resistance, as much as any paint I suppose, but I think the texture helps to hide marks.

 I could have hidden the seam lines in the enclosure using epoxy or bondo and a bunch of sanding and/or milling... when I got to  that decision point in the project, it seemed like a lot of additional work, and I decided to try to reign in my OCD at that point to save myself much frustration, and remind myself of the wisdom of Voltaire: "Perfect is the enemy of Good".

Ze Back Panel.

 The controller can use either T/C or RTD input, and I have brought both out to terminals on the back panel.

 Ground wire is connected to the shield of the T/C cable.

 Yes, there is a missing screw. We don't talk about the missing screw. That was a Very Bad Day.

Done.

 The controller is the auto-tuning PID sort, very easy to use if you are patient and follow the instructions.

 It's not as easy to use as an Omega, but an Omega is $200 whereas this thing cost me $20 including a SSR and heat sink.

 Sometimes Chinesium wins. :(

Which reminds me, I don't know where the instructions are any more. >_<

 note, later:

Now I just need to make something like it all over again for our espresso machine, which ships from the factory with small, click-disk type thermal switches. The inside of the unit is a dog's breakfast of wiring and water tubing.  Just replacing the switches ought to be loads of fun. •cough•wheeze•

 It would literally be easier to disconnect the thermal switches and leave them in place, epoxy a thermocouple to the boiler, connect the boiler leads to the temp controller and cover it back up.

 I'd better start thinking about another enclosure...

~≈{πŸ‘}≈~