Showing posts with label tools. Show all posts
Showing posts with label tools. Show all posts

Tuesday, September 22, 2026

If I'd known we were going to jam, I'd have brought my kazoo

 Gothsigh, grumble, and gripe: Operations stalled.  Kinda literally.

 I haven't messed with the printer for a few days because I am avoidant - like, it's a personality disorder, man.

 What I've been avoiding, until today (until some mysterious switch in my head got flipped the other way) is a filament jam in the extruder.  These were unheard-of with PLA, despite a really aggressive (non stock) tensioner and aftermarket... rims (had to say it) I mean extruder wheels.  I could make it quite tight to overcome resistance in the filament feed chain... like ferinstance when the reel is inside a dryer with stupid filament ports, outside the printer tent.  PLA tolerates a lot of squeezing and knurling.

 I switched over to some new TPU replacement (maybe, we'll see) which is a high flexibility PLA.  If you can see it coming now, why couldn't I see it coming then?

 Yup: I forgot to untension the extruder so while trying to load filament, the too-tight drive rolls squished the PLA-flex into funny shapes all around and near the bourdon tube and drive wheel, everywhere but into the tube.  100% my bad.  A right little mess.

 Unfortunately, with the printer inside the tent, it is a neck-craning pain in the, er, neck, to do anything to the extruder - even just adjusting the tensioner, never mind unjamming plastic bits from a tight mechanism and after five minutes of poking and proding with tweezers, dental probes, and a No. 11 X-Acto blade all to no avail, I walked away for a few days.

 There's always other stuff around this dump our majestic mansion that needs doing, after all.  Like all the things we should have done the first ten years we lived here, when we had money.  Cough, but I digress. 

 I really do not want to move the printer, I especially do not want to remove it from the tent unless I simply can't get this done any other way.

 Now it is time to dig into the extruder again (hopefully I can avoid disassembly) then see whether this flex PLA stuff can even be shoved through a bourdon tube at all, or if it requires a direct drive extruder.

 And where did my filament cleaners go? 😬

 I got the extruder wheel unjammed, still need to remove the bowdens full of filament and empty them.  Around then my leg started hurting again, so I'm not going downstairs to fool with the printer until it feels better.

 I'm also not working on shop projects, both for that reason and because my paint won't arrive until tomorrow, and because fucking Mouser canceled my order for bizarre reasons their abysmal customer service either could not or would not explain.  Meanwhile, they still show them in stock, but they won't sell me any.  I am so done with Mouser.  And why is an $11 relay now $30?!?

 ~≈{👁}≈~

Thursday, December 25, 2025

Tools For Christmas?

 If you're a regular reader of this blog, I hope you received at least one tool for Christmas, and I don't mean that one asshole relative coming over for dinner.  I suppose even a software tool would count.  So would a 3D printer, or just a hammer if it's a hammer you need and appreciate.

 Santa brought me two things I needed/wanted, both PPE; a pair of MIG welding gloves to replace the ones I wore out*, and a pair of leather welding spats to cover boots and lower pants legs†.  I really need those when I'm welding at higher currents.  Sometimes the spatter seems as bad as welding stick. :)

 So those were welcome indeed.  Also welcome was a high grade (Tripp Lite), steel cased, isolated outlet, RFI filtered, surge arresting, outlet box.  ie; ISO-BAR 6.  These units are very nice indeed, and this one  will go straight into the 3D printing lab/bench.

 And I got another present which I shant detail, because it's prurient / naughty and thus not suited for this blog.  So there.  Yes I know I frequently curse in my "family-safe" blog.  Shaddup. ;P

 Might not seem like much, but we're kinda broke.  The good news is, we're not really into the crass commercialism of the season.  We prefer giving things which are thoughtful and appropriate to the person, not expensive.

 Merry Christmas, and new tool wishes to all of you.

~≈{👁}≈~

___________________________________________
* pro tip: MIG welding gloves at the welding store are fifty bucks.
   The EXACT SAME gloves are sold in gardening shops as "rose
   gauntlets" for twenty-five bucks.  I like the "MUD" brand.
   You're welcome. ^_^

† this AM I happened to notice lacy holes in the cuff of my lounge
   pants.  "oh yeah," says I to myself says I, "I should wear my new
   spats AND stop being a literal 'pajama welder'."

Sunday, September 20, 2020

another thing about hot gl-- OH MY GOD WILL HE NEVER SHUT UP??

 So it turns out I may or may not have made a mistake in buying the 3M AE-II applicator.

 When I made the decision to buy it, I based my decision on the documentation I found on 3M's web site, which said that it is a low-temperature applicator, and I quote:

G - 3M™ Hot Melt Applicator AE II
Dispenses hot melt adhesive at a fixed temperature of 270°F/132°C. 

 Furthermore, it shows an orange applicator.

 That page does not mention anything about there being low and high temperature versions of the AE-II, it only mentions the AE-II as a low-temp... GUN. There, I said it, and you can't stop me from saying it again.  Ahem.

 So some glue sticks arrived which I had ordered.  And they were crap so I decided to send them back.  While shopping for The Right Thing, I stumbled across pages on non-3M sites which made it clear that there is a high-temp and a low-temp version of the AE-II, and in the other literature which I subsequently found on 3M's web site, it appears the high-temp version is blue, and the orange one, which I have, is a low-temp version.

 I pondered this for a bit, then checked the site where I had just ordered the new, high-performance industrial glue sticks... in HT versions.

 Huh: on their web site, the low temp gun is blue, and the high-temp gun is orange. Oh, what the hell!

 I wrote them an email and will hopefully hear back in the next business day or two.  Christ, who knew that having a decent hot glue tool was do bloody involved?

 By the way, you can make really sturdy fake spider webs using hot glue and a compressed air gun and a steady hand.  Makes a terrific mess, but if you do it right, it's about 1000x times stronger than rubber cement spider webs - more durable for decorations, completely unsuitable for being moved by actors - for that you want the rubber cement webs. ^_^ If you want someone to think they're real, you want rubber cement.

Happy Hallowe'en.

Friday, September 18, 2020

are y'all sick of hearing about glue guns yet? 'cuz I learned a thing...

 I was reading patents on glue guns (the way you do) and between the patents and the advertising, it seems most hot glue guns have had some kind of anti-drip gimmick for a long time.  Apparently, most of them have a check valve assembly in the nozzle - just a ball and spring, keeping the nozzle closed until a bit of pressure is applied to the glue to force the valve open.

 It was easy enough to look for this feature on the 3M, I just unscrewed the nozzle. Lo, there it was... brass 3M nozzle on the right (with ball visible at bottom of hole) and silver Arrow nozzle on left.

 I hadn't taken one apart before that I could remember, so I took the junked one apart, revealing its failure mode in all its splendor: 

(uh, look ↓ down ↓ there ↓ sorry I suck at page-setting...)


Somehow*, the glue had flowed back out of the heater and gummed up the works.  Oh well, so what, I have a new one.  I was more interested in the nozzle on the far right which, it turned out, could be unscrewed just like the intentionally replaceable ones on the fancy 3M unit, once the anti-unscrewing plastic collar was removed during disassembly.  I feel it was put there to discourage this. The nozzle assembly with its anti-drip valve need to be fabricated separately, then assembled to the heater body, which necessitates the threads, but the consumer isn't intended to take it apart, and they will, if they can... which means more returns...

And lo, once I dug the solidified glue out of the inside of that nozzle, I could see that the cheap nozzle has the same anti-drip ball valve feature!

 I didn't think about how I was going to write this when I took the photos, sorry.

Anyway, check valves in glue guns, who knew?

 During all this disassembly I spotted another interesting feature at the bottom of the hole in the heater of the 3M unit, where its nozzle screws in:


 I have expended a bit of skull-sweat analyzing this feature, and I have absolutely no clue what it does.  Do glue sticks need to be mixed after melting?  This is right before going into the nozzle.

EDIT, later: this might be intended to remove bubbles from sticks as they melt.  Bubbles could be bad, because air expands a lot more than glue when it get hot; bubbles in glue sticks could cause little pops and bursts of hot glue emission from the nozzle, something we all would like assiduously to avoid!

 Incidentally, the nozzle on the 3M unit is sealed with a conventional looking black O-ring, probably viton, maybe silicone.  The service temperature for Viton O-rings (200ºC) is sketchy-close to the melting temperature of low-melt-point dispensers, so maybe silicone.

That's all for today unless I think of something new, I just thought these were interesting fine points. 

Tool nerd, sue me.










_____________________________________________________________
*read as: "operator error" - I probably pushed too hard before it was fully
warmed up

Thursday, September 17, 2020

a few more details about the hot glue g- er, I mean, hot melt adhesive applicator

on the left: Old 'n' Busted

on the right: New Hotness

1881 silver dollar for scale. Also a flow pen, a pencil, a UV LED pen, and a twelve inch machinist's scale... for scale.

 Somewhere earlier, I claimed that the industrial production unit had ten times the heater power as my old consumer unit.  It turns out I lied.

 Just to check, I fished it out of the trash can, and it actually had a 40 watt heater, which I think I now recall was a step up from a 25 watt artsy-craftsy unit.

 So the new unit is more like 6.25 times as much power, and it is regulated with a PTC thermistor.

 I meant to also mention a little detail and forgot, earlier: the handle is very wide at its base, so even without the huge support bail installed, the gun is very stable and does not tend to tip over.

 Honestly, I can think of only one way this tool could be improved, and I'm tempted to write 3M and ask for it, though it would surely drive up the price, and market research would no doubt prove that I'm the only guy on the planet who wants this, but... replace the PVC-jacketed, slightly stiff power cord with a heat-resistant, rubber-jacketed cord (silicone or maybe neoprene) cord that is more flexible and limp.  That's it.  Change nothing else.

 If you use a hot glue gun much at all, and assuming you can pick one of these up at a reasonable price, (or you're sufficiently well-heeled that can afford to shell out MSRP)... GO BUY ONE.

I now have strong opinions about hot glue guns

 Excuse me, did I say "hot glue gun"?  I meant, "hot melt adhesive applicator" of course.

So anyhow, it has arrived, shipped in the same box it was photographed in for the auction:

This here is the 3M AE-II Hot Melt Adhesive Applicator.

So far, upon unboxing, I am fairly impressed on several fronts:

  •     It just feels solidly built. Well you'd expect it to be, given that it's intended to be used 8+ hours a day in a production environment.
  •     The cord is eight. feet. long.
  •     It has a pilot light. I didn't know it had a pilot light.
  •     It has two benchtop stands, a flip-out stand near the front, similar, but much wider and sturdier, to the ones on my previous units.  But another, enormous, much sturdier stand can be plugged into the base of the handle rendering the whole thing as stable as a pyramid - nearly impossible for the tool to fall over with it installed, however it may need to be removed (it just pushes in or pulls out in a second) to get into tight corners.


 I would say this is even worth the full-boat price of $100 if you can afford it, although I was much happier paying $40 + shipping.

 My glue sticks won't be here until Monday, so I won't be able to report on actually using it until then.  More as it happens.

Saturday, September 12, 2020

why do cheap glue guns take so !@#$^ long to heat up?

 Ever wondered?

 The answer has to do with economics on the one hand (no surprises there) and on the other hand, something called radiative equilibrium.

 We can't just run the heat gun at any old temperature, it has to hit a certain temperature range (≈265º F) and stay there.

 It just isn't economical to add a thermostatic switch or other reactive regulatory mechanism to the heating element on the cheaper guns.

 So the heating element is sized to be just enough to reach the right temperature before radiative equilibrium keeps it from getting hotter. Radiative equilibrium is what happens when an object radiates heat away at the same rate as heat is being put into it.

 Unfortunately, the power level at which this works for these small, hand-held units is so low that warm-up takes a very long time - up to 15min on my last one.

 The 3M unit I just bought must have some kind of temperature regulation (datasheet says "positive temperature coefficient" - a thermistor?) because it has a 250 watt heater, about ten times the power of my last glue gun, and the literature claims it is ready to use in 3 minutes.

Thursday, September 10, 2020

HOT FUCKING GLUE GODDAMN GUNS

 By the way, I say piss / fuck / shit / damn / hell / christ / goddammit a lot, and occasionally even cunt (a word I don't even like) - I mean... a lot, a lot.  I blame Uncle Sam and the USAF.  Don't say you weren't warned*.

 But this post isn't about my potty mouth...

--=O=--

 I have this love-hate relationship with hot glue guns. And one of the many offenses listed under the "hate" column is the bloody cheap dispensers.

 I have owned maybe three or four glue guns in my life.  Oh, when I think about the haunted house operations -- okay, maybe six or eight.  Each one was a bit of an upgrade over the previous, and a bit more expensive.

 The latest (#3? #8?) just went in the trash can not ten minutes ago.  It took me no more than that to come in to my office, pull up videos about hot glue guns on YouTube, find an 'Adam Savage's Tested' video about them, and discover that there is an excellent 3M product (shock, surprise, nobody knows adhesives better than 3M - nobody) which ought to be perfect for me, and will probably last me the rest of my life - it's an industrial tool not even aimed at craftsmen but aimed at people who put together custom cardboard packages or furniture - things like that - and do it all day long.

 There was just one fly in the ointment: those things were completely out of my price range.  3M makes good stuff, but their stuff also fetches premium prices, and those production-grade tools were out of my league, at least new... or so I thought...

 Seeing those 3M tools merely prompted me to see what was available on eBay, both new and used.

 Long story short, I just spent $40 on my fourth (ninth??) and I fervently hope, last hot glue dispenser, a 3M model AE-II, which normally retails for $100 or more.  But I found one new-in-the-box, open box, on eBay for $40 + $10 shipping from a reputable seller.  Half off, and still 2X what I paid for the last piece of consumer-grade junk from Arrow.  To be honest, $50 total was rather more than I was looking to spend, but I'm hoping it will be worth it.

 If you're dying for more details, 3M's datasheet for it is >here<.

 I will absolutely let you all know what I think of it when it arrives and I've had a chance to use it. That's because I'm making a fume hood out of... cardboard!  It's an interesting niche project for the winter, and it will let me try out my polyurethane-and-paper composite trick on a scale much larger than anything I have attempted before.  My intent and expectation is that once it's painted, it won't be easy to tell it isn't steel. And it doesn't need to be steel! (it doesn't need to be much of anything, really - just something that collects air flow in a broad funnel shape, and will stand up to minor handle and occasional bumps while hanging from the shop ceiling.)

 Since I also just ran out of glue sticks as well, I ordered 5 lbs (about 90ea 10" sticks) of Fixsy Premium high-strength (dark amber color instead of translucent white/clear) sticks which should hopefully last me the rest of my life.  I'll be sure to report on my opinion of those as well, but I bought them based on extensive user reports from people in crafting, modeling, and costuming forums so I'm not worried about the quantity purchase. Also I bought them through Amazon Prime so I can return them if there is anything unworthy about them.

 From the moment I stormed out of my shop in anger, through searching for what to buy, finding the Tested video, and buying the replacement glue gun on eBay, took a grand total of 15, maybe 20 minutes tops.

 Man, being a good little consumer is easy in the modern first world!

__________________________________________________________________________________
*seriously tho, I don't want to hear about it.  More than one old lady during my childhood washed my
mouth out with soap, and if that didn't change my mind, nothing you tell me will. Save your breath, goddammit.

Wednesday, September 9, 2020

random images from around my shop & their stories - - long

 

I finally remembered how to wrap text next to images, yay.

 Anyway, this is a funny: the original plastic knob broke, or fell off, so I replaced it with one from my knob bucket.  I'm pretty sure this knob came from a Mark Levinson amplifier. Which means the odds are decent that the knob alone is worth more than the rest of this cheap $29 soldering station.


 

 

 

 

--=O=--

 This is a small dream currently coming true. This is a rack cabinet (part# 308-95) for Durham Manufacturing's "Small Compartment Box" line of storage drawers.  They are super useful as organizers for drills, end mills, or other cutting tools, fasteners, clamping and fixturing accessories used on machine tools, and of course, small parts.

 The drawers themselves are super nice because:

  • made of steel, with a piano hinged steel lid so they won't break easily - I've owned and broken too many cheap plastic parts bins and organizers - the clear plastic one are nice to look through, but fragile
  • has a handle so you can pick up the drawer like a little suitcase and carry it to a work location
  • the plastic inserts are thick, durable PVC or PP (I'm not sure which, but it seems to be oil & grease-proof, so possibly PP) - they make one with adjustable dividers, but I don't like them because they ALWAYS seem to not stay put, or bend easily, or break, or have other problems - I like the very solid fixed bin versions, and there are several designs to choose from, including no insert at all
  • the drawer lid fits flush agains the bin divisions of the insert, and it has a snug latch, so when the drawer is picked up by the handle, the contents in the bins stay put (provided the bits are bigger than about 1/4 inch) - this is rather a big deal
  • racks are stackable, and there are risers so you can mount one on a bench and retain the use of most of the bench surface

 These are somewhat expensive compared to plastic versions you can get in hardware stores, so when I first saw them in the old Enco catalog, I thought I would buy a few drawers first, since they are only twenty bucks or so each, then later, when I got tired of shuffling them, I would buy one of these racks, probably the 4-drawer.  So I bought my first drawer and promptly fell on hard times and couldn't buy anything more for a long time.

 TEN YEARS LATER, I finally feel sufficiently flush to buy the 6-drawer rack.  I'll fill in the other drawers in the coming months.  You can get these from Amazon at competing prices, although I am mildly cheesed off that they do not have all the models of drawer inserts available which Durham makes, so I am looking around at other distributors like - (ugh!) - Grainger.  Also Grainger charges top dollar.

RIP Enco!

--=O=--


 Honestly, if you don't know who this is, I feel sorry for you. This is Beaker, from The Muppet Show. He's about six inches tall sitting down, and was a gift from someone who appreciated the Mad Scientist in me.  I've actually received two; I gave the second away to a friend's kid who is a huge fan of Muppet Labs.  Huh: no one thought to give me a Dr. Bunsen Honeydew.  I think the implication might be that _I_ am Dr. Honeydew.  But I have all my hair!  Anyway, Beaker sits in the unfinished wall above my shop bathroom door.  Beaker has seen some shit.

 

 


 

 

 

 

 

 

--=O=--

 These slogans are on the shelf over the doorway inside my shop, to remind me that if I want to make a living (or at least have a small side-business that actually generates any income at all) then I have to deliver; I have to get shit done.  It's a reminder that work I do for $ / others - even friends - has  deadlines and expectations attached to it, unlike work I do for myself.
 
 

 The two lines are, of course, taken from the infamous and nasty (but also brutally true) speech delivered by Alec Baldwin in "Glengarry, Glen Ross".

 

 

 

 

--=O=--

 At the entranceway 'twixt the garage and my shop and it pretty much speaks for itself, at least the actual sample foot-hazard attached to it should.






This is posted in the shop bathroom, but it should be at the entrance to the garage.  You'd be amazed what some people will whine about.  Some people don't get invited back to my epic house parties when they do that.









 

--=O=--

 

As a general policy, I don't do rush jobs.

--=O=--

 What indicator holders are good for, part 117: 

 In this case, I needed to measure the taper inside the spindle nose of my lathe, to identify what the hell taper it is. (I'm still not sure, but it's not Jacob's, Morse, or any collet that I can identify. I am so over the piece of junk.)

 So one indicator is measuring the travel distance and the other indicator shows the change in diameter over a given distance.  With a little math or trig, you can then derive taper-over-length or an actual angle, as needed.

 

 

 

 

--=O=--

 

 This is an inexpensive ($30 - $50) Digital Read-Out attachment for the quill of my mill.  Someone gave it to me for free, but it lay around unused for years because I didn't have the mounting bracket, and I didn't really need it.

 Since I started my recent initiative of cleaning up and fixing up my shop and its tools, I decided it was past time for me to either give it away or get it  installed.

 So I ordered the bracket from Shars, but they didn't include the two little clips which appear to be a part of the bracket, they are shown on the parts list and drawing included in the box... but they weren't in the box.

 Now when I asked them about this, Shars proved surprisingly un-helpful, and I became quite pissed off at them.  They insisted the two little clips always come with the DRO unit and that they had no source of them otherwise!  And note: if you buy the DRO unit and the bracket together, you get the clips.  Someone screwed up their purchasing and they are making it their customers' problem and I don't like it.

 So I made myself a bet: I bet myself I could mill my own little clips from solid aluminum - nicer than the stamped sheet metal clips that were supposed to be included - before I could get a reply from the seller.  I won that bet.

  Shars sells some okay bargains - caveat emptor- but when it comes to customer service, they are hopeless.

 

 

--=O=--

 

This is the label on the reversing switch of my mill.  It is a piece of obscure early hacker humor...

You can read the origin story >here<.

 I once had an actual "Magic / More Magic" switch on one of my own computers, and it was functionally useful: 

 When the Amiga computer was a new and glorious thing, I owned a 2000.  A new boot rom was released, and it was desirable, but it also broke a few games.  It came to light that one could "piggy-back" (by soldering) one of the ROM's on to the other, leaving out the enable pins, and bending both of those outward. Then you stuck the stack into the socket, and wired the two pins to a double throw switch; which ever pin was grounded was the enabled ROM.  All you had to do was turn off the machine, flip the switch, and reboot.  A terrific and easy hack back in the day.

 

 

--=O=--

 Now I'm off to get my spine zapped with high energy radiation (taking pictures of my innards! Gadzooks!) so if you're into praying, please pray that I do not have any ruptured disks or other spine damage, and that my recent godawful back pain is "merely" pulled muscles or a torn ligament / insertion or the like. O_O

Monday, August 31, 2020

shop safety - lifting

 I now have a back injury - a pulled muscle in my lower back - which hurts like the devil and is severely limiting motion.  I've done this sort of thing in the past, not that it's a good idea mind you, and I expect it will be better "soon" which means it could be magically gone by tomorrow afternoon, or it could still be aching and stiff a week from now.

 The cause was two-fold: yesterday, I removed the rotary table from my mill so I could:

A) tram the head, since I had taken it out of tram to cut something on an angle a while back and

B) figure out where the non-squareness problem was coming from between the rotary table and the vise
(it turned out to be rust on the bottom of the rotary table - to be fair, it came that way and I forgot about it - this thing is not trivial to turn over)

 This involved setting it down on a low storage place, something I should not have attempted alone.

 That alone might have done it, although I hadn't suffered any symptoms today, until... I was again working on the mill and leaning over things, straining my lower back... then suddenly something spasmed and I was in agony.

 Wouldn't it be nice if one could afford to have such things made out of titanium, say, instead of cast iron?  As it turns out, you wouldn't want to do that, because metallurgy and a long explanation I won't go into, but the short answer is that for the purposes of building these specific devices, either steel or cast iron is absolutely desirable, even if we could afford (the much lighter) Ti.

 So either I can only install and remove the rotary with help from another strong person, or I have to get a shop crane of some kind.  I haven't the space for the traditional automotive shop crane, like this:


 Those are cheap, and lift up to 4,000 pounds depending on boom position, but even folded I have no room in my shop for one.

 A much sexier option is the Sky Hook™ line of material handling shop cranes:

 There's a whole range of these things, large and small, with various mounting options for mounting the crane to mills or lathes or other machines, they can also be mounted on rolling floor stands or on carts too.

 It uses a machine (think cyclery) link chain, so the load won't spin. And based on reviews and videos I've seen*, they're well-designed, well-made, and a pleasure to use.

 Unfortunately, they are priced well out of the reach of the average amateur consumer - they are strictly for companies with a healthy material handling / safety budget.  I've saved an eBay search anyway, in hopes that a used one turns up in my local market (they are heavy, I'd rather not ship it) but I am not holding my breath.

 Maybe I'll win the lottery.  Not sure how that works - do you have to buy tickets for that to happen?  ;D

__________________________________________________________
* reviews and videos about the Sky Hook:
https://youtu.be/mCufgAwqhac
https://youtu.be/sWMmH6coe7M
https://youtu.be/aZItaoyndAc

Tuesday, August 25, 2020

The Ghost Ship(ment)

 My face (shell) milling cutter has finally arrived...

 

 I may be expecting too much, but so far I am not impressed.

  I haven't done a good cutting test yet because after I installed six inserts, I was shocked at the variations in cutting insert tip height when I measured the thing on the plate, at which point I stopped to figure out what was going on.

 Well, it turns out there are two things going on: 

 Thing One: the inserts themselves vary in dimension by a surprising amount - from .738" to .746":

 At first I assumed this was just shit manufacturing, but when I decoded the entire insert call-out code (APMT1604PDER) I discovered that this is a very low-tolerance insert (that's the 'M'), suitable only for roughing.  These inserts measure within their specification, they're just cheap-ass, low-grade inserts. Well, I can buy others.

 Thing Two: the insert mounting pockets in the shell itself vary in height by several thousandths at least; I haven't completed a formal survey and written down the numbers.  That is NOT normal, and it's not in anybody's specs!  For a shell mill to provide a good surface finish (and they are capable of very good surface finishes, when the inserts are right) the inserts must all be at the same height.

 I've asked the seller for clarification, details, specifications, manufacturer, explanations, etc, but I don't expect to get anything useful because China.

 So, another painful - but not terribly expensive - learning experience.

  And amusingly, it may be possible to even up the cutting tip heights by measuring all the pocket heights and installing the appropriate over- or under-sized insert in each so that the height differences cancel out as much as possible.  Okay, perhaps not so amusing to actually do in practice.

 Gumble.

tapometers, percussive tweakers, and swing presses

 In other words... hammers.

Such a simple thing, a hammer: just a hard weight on the end of a handle, also known as a rock tied to a stick, also known as a club, and if you take away the handle, you've got the very first tool ever used by a proto-human.

 The expressions in the title line are just a few of the many fun phrases we humans have come up with to describe our favorite tool, the one used for one of our favorite activities: bashing stuff.  Here's a few more...

  • bash-driver
  • thumb detector
  • jeweler's x-ray
  • micro-adjustor
  • attitude alignment tool

 I'd be tickled pink to hear of any others my readers might know.  Feel free to comment with others.

 Ever since I was a kid, I've found it amusing that we humans need more than one kind of hammer.  I think at some early age, I had the notion that being able to hit one thing with another thing was a problem easily solved using whatever was handy, and that hammers were sorta glorious luxuries which one would use if one happened to remember to bring it from the toolbox.  If one forgot, a nearby adjustable wrench, or the meat tenderizer from the kitchen, or a brick - seemed perfectly adequate.

 My epiphany - that bashing stuff could be a craft in itself requiring specialized bashing instruments - came when my mother decided that we were going to tear up the driveway behind our house, to plant a garden.

 Said driveway was, at the time, 80 years old, six inches thick, and laid down by people who really cared.  That concrete must have taken a year to cure, because despite having zero reinforcing rods or wire in it, it was un-cracked, as solid as bedrock, and as hard as a bad day.  The solution to this inconvenient mass was an eight pound sledge hammer and a twelve year old boy who had read Tom Sawyer.  As a hormonal, frustrated, abused, slightly mental teenager, I had anger and other emotional issues to work out, so I thought that being given the opportunity to destroy something with a hammer was a fine opportunity, and I set to work with gusto.

 I mention Tom Sawyer because I hadn't been breaking cement for more than ten minutes when a small crowd of curious kids gathered around.  Destroying things is one of the natural passtimes of children, so once they got the idea that I was being allowed, nay, even encouraged to obliterate part of my family's  property with a hammer, well... that made me seem to them like the luckiest kid on the block.  Presently, one of them asked if he could have a go, and the rest you can easily guess if you have read Mark Twain.

 That unforgettable afternoon left an impression, I think: that specialized bashing implements are even cooler than regular bashing implements. (and also that other people are easily manipulated into doing your work for you - how then did I ever fail to go into management?)

 Some time after I left home and moved into an apartment, I bought my first hammer - a claw hammer with a fiberglass handle.  I bought one more - a short handled heavy "drilling sledge" with a steel handle - all one piece - at some point during my first marriage, in order to poke a hole through the foundation wall for an electrical conduit.  That seemed to suffice until my second marriage and my second house, when I accidentally started a collection.  I haven't gone nuts with it, but the other day it occurred to me to wonder how many hammers we owned, so I went through the house and shop and collected them all:

...and yanno, seven doesn't seem like all that many, even to my wife, because there are no extras and each has a purpose.

from L to R:

  •  small ball-peen used for metal-working, one of three frequently-used hammers which hang on my workbench
  • small claw-hammer that my wife owned when we first met, lives in a toolbox in the house
  • the fiberglass clawhammer I mentioned above, it also lives on my workbench
  • orange soft plastic "dead blow" hammer, the head is filled with steel shot so it has no rebound - mostly used to seat work in the mill vise
  • a "heavy hammer" or "club hammer" - 5 lbs, also lives on my bench
  • a "drilling sledge" - 5 lbs, originally used for hand-drilling through masonry using star drills
  • full-sized long-handled eight-pound sledge - I bought it to break up part of a concrete sidewalk. The wooden handle it came with broke when I got tired and missed something with the head, hitting the object with the handle. The yellow handle is a fiberglass-reinforced plastic handle claimed to be unbreakable which epoxies into the head. It's held up amazingly well with a tremendous amount of use

 This seems to be about all the hammers I can find a use for.  There are a hundred other specialized kinds, from hammers used by blacksmiths to hammers used by geologists exploring for oil or uranium.  Here's a guide showing fifty-five different kinds: https://www.engineeringclicks.com/types-of-hammers/

Saturday, August 22, 2020

Machinery's Handbook

 In 1914, at the dawn of the industrial age, a thorough reference book was published for the very first time, on the subjects of metals, metal-working and the machinery used for same.

 Machinery's Handbook - referred to by many as "the bible of mechanical engineering" - was intended for machinists, engineers, and metal-workers, and contains a vast trove of information on every aspect of metal-working: trigonometry, rearrangement and development of formulas, mechanics, strength of materials, threads and fasteners, stamping, welding and cutting, machining of various metals, gear design and manufacture, cutting speeds and feed rates for machining and many other topics besides.

 Machinery's Handbook was the first of its kind and it came out so early that nobody has ever really come out with anything that competes with it - it is unique.  It has been in continuous publication for 100+ years

 The handbook is so popular - virtually every English-speaking machinist in the world has a copy - that most "machinist's tool chests" from Gerstner, Kennedy, etc, all have a special drawer which is sized specifically to accept (just barely) the 4.6" x 7" 2,000 page book. I don't keep mine in there because the drawer is only JUST big enough; it's hard to get the book in and out, so I keep tools in that drawer, and the book I keep on a shelf - I don't know any machinists who ACTUALLY keep the book in the tool chest drawer, but that's what that drawer is there for.

 You can read the history of the publication here: https://books.industrialpress.com/resources/history

 If you prefer videos, Mr. Pete (AKA 'tubalcain') has a good one: https://www.youtube.com/watch?v=AuJpnJLoAE8

 Because it's a reference book meant to last a lifetime, and is made with high quality printing, paper, and binding, it's expensive. I couldn't justify the cost to buy one new, but I scored a copy at an auction for nearly nothing; I won a cabinet shelf full of metal stock, odds & ends, and the Handbook... for $5.  Go to auctions, friends and neighbors. ;)

 You can get used copies in good condition for great prices at Alibris - my favorite book-finding clearinhouse for small business book-sellers. Always go there first before trying Amazon or any of the big-name book sellers. Not only will you save money, you will be supporting small business owners instead of big corporations who enjoy putting small business book sellers out of business.  Seriously though: fuck Barnes & Noble.

cam-lock lathe spindle fittings

 I'm gonna talk about one of the downsides to buying used equipment. The too-long-didn't-read version is simply this: "if you consider a used machine, ensure it comes with every possible accessory you might need, OR ensure that it's standardized enough that common aftermarket accessories will fit it."

 The rest is details, examples, and supporting evidence.

 My lathe was built in the 1970s by the one of the predecessor factories which later became the SIEG group in Taiwan. For those who aren't familiar with the company, Shanghai Industrial Electric Group (this may not be the correct acronym - the company doesn't talk much about its early history, because it's all embarrassing) is the manufacturing source for Gizzly, Jet, Enco (now defunct), Turn-Pro (MSC's house brand), Rong Fu, and many other brands of low-cost machine tools. 

 In the early days, before the existence of Jet and Grizzly, everything SIEG made was junk. Eventually, with the help of (semi-) modern manufacturing and quality control methods, their quality began to rise. Even so, Grizzly and Jet have a two-step manufacturing process, with the final finishing and quality control being done in the states. They are still inferior to the best machines made by the mainstream famous brands, but the newer machines can be entirely adequate for many hobbyists and many small businesses.  I worked in a high-technology laser factory for a few years, and we used a cheap Rong Fu mill to cut open bad laser tubes to examine them, it was good enough.

 Sadly, mine is not one of the newer machines.

 Several times in recent years I have wished for the ability to turn items between centers on my lathe, but I do not have a center or other fixtures (ie; lathe dog plate and lathe dogs) to fit my lathe spindle. Very well, I decided this morning I would start learning about my lathe spindle and what things I would need to fix up my spindle with a center. A secondary goal was to find out how difficult / practical it might be to fit my spindle with a collet closer (which I would almost certainly have to make from scratch, but there are multiple designs and projects for making them, including a very nice one in Home Shop Machinists magazine about ten years ago...)

 So next, I'm gonna blather a little about lathe spindles and chucks and other accessories.

 At present, there are at least five different styles of spindle on lathe headstocks, and each style comes in several sizes.

 In the earliest days of lathes, chucks and dog plates were attached to the spindle by the simple expedient of threading both and assembling the chuck onto the spindle like a nut onto a bolt.

 But this method had serious problems, one of which my high school metal shop teacher lectured us about over and over.  And despite his  lectures, I once witnessed exactly what is described next, first-hand, and it was every bit as exciting as described even with a "small" chuck weighing only 75 lbs or so...

 "Although cheap to manufacture and perfectly adequate for most purposes, especially amateur use, threads do have serious limitations centred around safety, rigidity and ease of removal and replacement. To take just one example: a threaded fitting cannot safely be run backwards and, whilst a chuck might happily stay in place as a lathe accelerates up to top speed in reverse, once there it cannot be so easily stopped. Legion are the number of serious accidents caused where an operator has stated a lathe in reverse, realised his mistake, and then (without thinking) applied the spindle brake. Once the chuck starts to unscrew the workman can do nothing but watch in horror as the 200 lb mass, rotating at 800 rpm, accelerates down the length of the workshop, smashing machines and people unfortunate enough to be in its way." -- from http://www.lathes.co.uk

 One of the clever dodges that was dreamed up to address this is the cam-lock spindle (standards: DIN 55029, ANSI B 5.9 & ISO 702/I)

 My lathe is equipped with a D1-4 cam-lock spindle, and when I bought it used, 30 years after it was made, it came with just one 3-jaw scroll chuck; no spindle center, no dog plate for use with said center, and no 4-jaw chuck.

 Sadly, the internal bore shape of the spindle is not defined in any of the cam-lock standards!

 My spindle does have a taper of some kind inside, but the spindle bore is quite large (3.5 - 4.0 cm or so) and any regular center which fits it would be enormous, so I assume there is some other equippage which fits the spindle and then accepts normal centers... I just don't have that item.

 That internal taper - I haven't determined what it is - does suggest strongly that a collet closer could be fitted, which is nice, but that's not my priority rght now, having centers is.

 The next step is probably to identify that internal taper using a dial test indicator mounted on the saddle; n thousands of radial change over N distance converts easily to an angle with either high school trigonometry (which I can never remember) or the trig tables in Machinery's Handbook*.

 If I get really desperate, I'll hop into the forums for either Home Shop Machinist or Practical Machinist, but I gotta tell ya: there are helpful folks in those forums, and there are some real elitist assholes who have zero interest in being supportive of beginners, which to me is a baffling attitude - so if you tread those halls, tread with care and be prepared for a few of the denizens to shit on you. For me, those forums have become a last resort, I'm more likely to watch four hours of YouTube videos looking for the answer than I am to spend one hour reading those forums. YMMV.

_____________________________________________________________
* if you don't know about Machinery's Handbook, you need to; I'm gonna
write up a piece on it in my next entry.

Sunday, August 16, 2020

Q: What tools or machines do you want / need / plan to get, that you don't have yet?

 1. a floor-standing, vertical band saw, with large table, variable speed, blade welder & grinder, all that. I dream of a Do-All, but I'd settle for a Grizzly or Jet. Prices for used vary wildly of course, but one can plan to spend anywhere from $2k on up depending on size, features, brand, condition, etc.

2. a sheet metal "3 in 1" machine: shear, brake, and slip roll, 30" wide or so.  I haven't looked in a while, but that last time I did, they were about $300 - $400 for one this size (smaller).

3. a sandblasting cabinet, floor standing, about 40 pounds or so. These are surprisingly cheap, and a few simple and easy upgrades can make one of these into a super-tool.  This will save enormous amounts of time and costs pennies to operate. A filtered vacuum and full enclosure keeps dust out of the shop. I've used a friend's and they are wunderbar!  I'm seeing these for about $200.  A cyclonic dust collector attachment adds another $200.  Requires an air compressor with large flow (volume) capacity, which I have.

4. a shop crane, probably "2 ton" size. $250 - $500

5. a different welder, probably an all-mode power supply with a MIG whip, TIG whip, and a spool gun. Blue. ;)

6. a plasma cutter would be REAL NICE, faster, more economical, and safer than the oxyfuel torch I use now.

 I think I even blogged the rebuild process for that imported compressor right here in this blog years ago, but I think the pictures might be gone now.

 But on top of new machines or tools, there is always tooling for the mill and the lathe which can amount to an infinite variety of things, and an infinite amount of money... improvements in welding capability and my welding table... small machinist's tools...

So yeah, if any long-lost rich uncles feel like dropping a surprise on my head...

EDIT: many edits. There were originally only three items...

EDIT RIDES AGAIN: Because I could really have used the sandblasting cabinet for virtually every steel project that got painted I've ever built, and because it's so much cheaper than I thought it was, this is probably going to be my next big-ticket purchase. Even fresh new steel comes with mill scale which has to be removed before welding or painting... I am practically salivating over this item.

where's Kevin Kostner when you need him?

 Regarding that elusive milling cutter which is allegedly on its way to me... it turns out that SpeedPak*, the carrier service used to ship my cutter, hands off their shipments to... the United States Postal Service.

 Now, it really wasn't all that long ago when this would have been happy news indeed because for my entire life, since I was a child in the 1960s until just about two weeks ago, I knew I could rely upon the USPS to do a good job.

 But of course, thanks to our Fearless (Brainless) Leader, the speed and reliability of the US Postal Service is out the window.

 So naturally I doubled down instead of being cautious -- just like our president would!

  Yesterday I ordered, via eBay, a Noga style (Shars, in this case) dial indicator holder, like this one:

 

 This is the second indicator holder I've ever owned, and I bought the first one - even cheaper, a HF PoS, at Charlie's Second-Hand tools for nearly nothing. Before this month, I've gone without, or rather, I've made my own ways and means on the spot as needed. And it's been a pain in the ass, too.

 What makes this style of holder pleasant to use is that the one knob in the middle locks up all three joints.  So you have fastened the magnetic base to something, you can hold the indicator where you want it, use the knob to move the arms to a reasonable position, and then with a twist of that same knob, lock everything up. It's like having a third hand. Another convenience is a fine-adjustment built into the indicator holder, making setup a little easier.

 The other item I picked up is a simple bracket assembly...

 which lets me mount a cheap DRO, or Digital ReadOut, like this one...

 

 to the spindle feed of my Bridgeport mill, like this:

 

...sorta, except the above photos show a method which requires drilling a bunch of holes in the mill, whereas the Shars bracket mounts using the scale screws on the left, and tracks the movement of the quill by picking up that great big round hole in the front of the quill stop. Gotta love this guy's quill feed wheel tho... 

EDIT: I'd quite forgotten, but both these items came from the same seller, who shipped them via FedEx, and they are guaranteed to be delivered by the 20th. Huzzah!

__________________________________________________________________________
* a partnership between eBay.cn and OCL and the default shipping option for sellers in China

Thursday, August 13, 2020

Face Cutter, O Face Cutter - where the fuck art thou, O Face Cutter?

 Mah new milling cutter has vanished into that interstitial Hilbert Space between two parcel carriers:

"Orange Connex" (OCL) in China, and... whoever they handed it off to in the USA after it cleared customs.

 I am used to dealing with the Chinese Postal Service (which isn't too bad, honestly) which hands off to US Postal Service here.  They seem to inter-operate their tracking numbers as well, which is awfully nice.

 This shipment's tracking number works for OCL only, which ceased to be relevant once the shipment entered U.S. Customs. The shipment cleared customs on Aug. 7, and according to OCL's last hand-off message, "Arrived At Destination Hub".  Well, they sorta neglected to mention WHICH "destination hub", ie; WHICH SERVICE it was handed to - the US Postal Service, UPS, DHL, FedEx, Billy-Bob's Bait & Parcel Service, or what.

 I asked the seller whether they knew who OCL hands off to, but they have not yet responded.

 It is not likely to be US Postal Service, because we have a magical service available called Informed Delivery, which sends us, via email, a notification of every single piece of snail-mail they receive which is destined for us, along with a B&W photo of the item, regardless of whether it is personal, commercial, junk mail, advertising and coupon fliers, or a package.

 US Post Informed Delivery doesn't know about any packages coming from China, so presumably it was handed off to one of the commercial services.  I wish I knew which one.

 The seller predicted a delivery time of August 14 - September 9, which I accepted when I bought it, so technically it's not late, and really, I have no reason to doubt it will turn up eventually... I'm just spoiled by the modern world, and I'm bored and eager to get my grubby little mitts (er, well, grubby large mitts) on the thing so I can evaluate and use it.

 UPDATE: jackass seller responded with a bunch of blather about why my package could be late - I never said it was late - and they failed to answer the one and only question I asked.

  So I asked again, and explained why I was asking (which was none of his business, actually) and I held his little baby hand until he stopped crying, but his Feedback-O-Meter is winding downward rapidly.

Monday, August 10, 2020

whither video?

 I realized that all the video channels I watch - including the folks I called out in a previous post - are using nice cameras on tripods, and that shakycam BS taken with a phone is going to annoy ME, never mind be unacceptably amateur-hour for my tastes.

SO...

 I'm going to wait until I have the dough to spare for a tripod and a Go-Pro or similar (or I figure out the video recording issue with my SLR), before I attempt to make actual, long, lecture-y, talking sorts of videos.

IN THE MEAN TIME, sometimes a picture is worth a thousand words, and a video is worth, um, mumble frame rate times minutes of running time... well, you get the picture.*

So I'll occasionally use my phone to shoot shorts bits of video, like this one:

Oh crud, sorry about the background music, I forgot to mute the mic.

 That piece of steel which is floating across my surface plate is one of three pieces of scrap low-carbon steel I've been working on to make flat and parallel.  I'm trying to prove that I can make gauge blocks effectively out of junk, and without owning a surface grinder.

 With one proviso: I'm not planning to finish them to any particular dimension. So if they come out = .17278xx but reasonably flat and reasonably parallel, I'll be pretty darn content. (the xx's are values I care about, but won't be able to measure with any accuracy any time soon because my name ain't Tom Lipton)

 I do however, intend to make all three equal, otherwise they'd really be useless.  The point is to prove the process, but I need better measuring tools - some actual gauge blocks, say - before I'll be ready to try making any to a specific dimension.  Even so, with almost minimal effort, they are flat enough to float, which means they are trapping a layer of air - thinner than .001 in / .025 mm - between the block and the plate.

 To do that means that the microscopic features of both surfaces have to be very low in height - the surface has to be very flat and very smooth - for this to work. Realize there is no lubricant present but air - the surfaces must be very clean and free of finger prints, etc.

 This is actually already more flat and more smooth than I'm even ready for; the three blocks need more work on parallelism before they are ready for lapping; they are more like small angle blocks†... and they are not supposed to be...

___________________________________________________________________________
* sorry not sorry
† .0382º if you're curious, or 138 seconds of arc, or .00067 radians...

Sunday, August 9, 2020

masters, teachers and peers - machinist edition

I call these guys The Machine Shop Mafia.  They all know each other via YouTube, and a bunch of them have been getting together at meet-ups around the country for various things.  I haven't included everyone in that circle of YouTubers, only my favorites who I follow faithfully...

Tom Lipton, OxToolCo - Tom is like the uncle I never had but wish I did.  He seems so genuinely nice, and calm, and un-excitable that for me, watching his content is like a mental oasis, a micro-vacation.  Tom is a lover of tools, especially precision measuring tools, but he is also a lover of precision generally, and therefore, he also owns and obsesses over the laboratory standards and instruments which are used to calibrate the high-precision measuring tools which are used in a machine shop.  As a tool fanatic, he also has a great appreciation for shop-made tools, the unique fixtures, tooling, and problem-solving widgets that machinists - or indeed, anyone with opposable thumbs - create in order to make their daily work a little easier.  I have made many tools to solve problems in the shop, but none of them were useful more than once, and none were made to last.  Tom's own work and his appreciation for the work of others, inspires me to try to do better. -- https://www.youtube.com/user/oxtoolco/featured

Adam Booth, Abomb79 -  Don't take this guy on in a 4-jaw aligning competition. As near as I can tell, and I apologize if I got this wrong, Adam is a 3rd generation machinist, who worked in his dad's shop, who in turn worked in his father's shop.  As a result, Adam strikes me as the consumate competent machinist; he's probably forgotten more tricks and tips than I will ever know - every time I watch one of his videos, I discover some new time-saving technique that makes me smack my forhead, or the existence of a tool I didn't know existed and now positively must own because it's fundamentally better than what I've been using all my life. -- https://www.youtube.com/c/Abom79/featured

This Old Tony - Tony is the funniest guy in The Machine Shop Mafia.  Blink and you'll miss it.  He does a lot of work restoring or upgrading eccentric old machine tools.  He seems to get a lot done in a very short amount of calendar time, so I wonder whether he sleeps. -- https://www.youtube.com/c/ThisOldTony/featured

RobRenz - I found RobRenz two days ago via some comments that Tom Lipton made about him in one of his videos. Anybody that Tom thinks well of is somebody I need to know about.  He seems to be into very high precision (physical) metrology. -- https://www.youtube.com/user/ROBRENZ

Cà Lem - I just found this fellow this morning, via a comments conversation between Cá Lem & some of the other fellows listed above. He is a machinist, makes nice tools, also does restorations -- but as far as I can tell, HE'S JUST A KID!! - https://www.youtube.com/c/CáLem/featured is his channel, but watch this amazing video to get a perfect summary of why his channel is so respected by the other YT machining pantheon: https://youtu.be/skMvRMGVybM

Clickspring - Does a lot of clock related stuff.  Features a lot of very finy, small, fiddly work, like a jeweler, clock-maker, or watch-maker.  Beautiful craftsmanship.  I learned about how to "time" screw heads from him. -- https://www.youtube.com/c/ClickspringClips/featured

 These are the machine shop folks I look up to, when it comes to truly advanced machining and toolmaking.  But I am not qualified to teach what they do.  I intend my blog to be for beginners.  I consider myself basically competent as a home shop bodger.  I do not call myself a machinist because I am not one - I have not worked as one professionally, nor do I have the skills of a professional.

When I watch the videos of the people listed above, I am very much a dog watching origami.

 Fortunately, I have a good friend who is a professional toolmaker, with whom I have a pretty good relationship, although I think he has done me far more favors than I have done for him.  I also did a very small amount of paid part-time (piece) work in his job shop which AFAIK worked out fine for both of us, which helped me understand some shop viewpoints and "ways of working" which were of a larger scope than the simple tasks I was performing.

 He helped me evaluate and decide on buying my lathe, for which I am grateful, and much more to the point, he sold me a Bridgeport for well below market value for which I am in his debt.  And he lets me bug him with the occasional question.  I can't figure out how to pay this kind of thing back, either, and it eats at me sometimes.  I have a lot of treasured friends like that, it is the way I am most fortunate, and I am baffled how I earned such people in my life.

 Frankly, that's how most of my professional education has gone - I hang around people who are smarter than me, I pay close attention to what they do and how they do it, and I ask a lot of questions.  For most of my life, I have managed to get paid to do this - I've been doing a sort of high-level On-The-Job-Training, without pursing any college.  Bonus: many of my friends are professional nerds with similar shared interests, so much of the time I (used to) spend socializing or recreating, I was learning tech skills too.

 I grant you it's not for everyone - especially if you are a Reading/writing type* learner.  Although I am an avid and strong reader, that's not how I learn best - I am half Visual and half Kinetic style learner, in that model, so YMMV.

____________________________________________________________________________
* the so-called "V.A.R.K." model of four types of learner, developed by Neil Fleming in 1987

Saturday, August 8, 2020

strange dreams

 I took a nap (something I almost never do) and I dreamed (something I don't do enough of, because I use weed too often) that I had made some little shop tool for a lark and sent it to -- huh!  I guess it was a dream-amalgam of multiple people that I watch on YouTube: Abom79, OxToolCo, and ThisOldTony, on YouTube, and "he" mentioned it with pleasure on his channel.

 I guess I know why I had the dream; watching those guys has rekindled my interest in making things in my shop, rekindled my interest in machinist and tool-making skills, and they are the reason this blog has been rebooted.

 Well shit: with that obligation in mind, I now feel compelled to send one of them in particular (because one of them was more inspirational to me than the other two - something that he will appreciate and use. 

 Having a smoke in my shop just now, right after I woke up, I immediately thought of two shop-made tool ideas, neither of which I have ever seen anywhere, and both of which would be terrifically handy: one would be useful all the time, as it is a method of making a very fine adjustment attachment for an indicator holding arm.  This idea was partly inspired by the incredible amount of suck contained in the so-called "fine adjust" of the cheapo Harbor Fright magnetic base I bought yesterday.

 The second is a small Jacobs chuck with copper-faced, steel-backed jaws; to be used for holding work, not a tool.

 I know how to build the former, it's just fiddly. I don't actually have an idea yet for how to make the latter; but it's a neat idea, I'll have to think on it.  Also, I don't own (yet) the required tools and materials to make the indicator holder, but the materials are cheap and the tools are on my list already so when I have them, I can start working on it.

Sadly, I have a bad track record for finishing things - I hope I get it done while he's still alive. >_>