Showing posts with label mill. Show all posts
Showing posts with label mill. Show all posts

Monday, October 5, 2026

Ohhh, so that's why we bake the enamel one layer at a time!

That paint was harder than a bad day.
 I just now finished this.  It took me a lot longer than it should have.  The painting was routine.  Getting the paint off the lettering was not.  It turns out that baking enamel on as I do has the desired results - that stuff gets tough. It will not crack or chip, and it resists abrasion.

 I started with wet-sanding, but this went very slowly, even with nice, fresh/sharp, silicon carbide paper in a semi-course (200) grit.  Harrumph.

 Next I tried mounting it on the mill and running a little (sized for a Dremel) convolute abrasive point over it.  That seemed to move the paint around a bit.

 Finally, I decided to get aggressive; I put my largest fly cutter in there.  That did the trick.  Even so, it required multiple passes, and I had to touch up the 'ON', 'OFF', and the ®egistered Trademark symbol by hand-sanding with one of my paint-stirrer sanding sticks.

 The enamel finish was dulled in a couple of places by my carelessness during the first attempts to do it, and I haven't decided what to do about that.  First impulse is to mask off the shiny bits and just spray, but I worry the mask boundaries will look like dog yack.  Actually I think I will try wiping the dull spots lightly with acetone first.  We'll see.

Er, well, it turns out I own a buffer, with a selection of wheels and compounds.  I forgot. >_<  I'll mask off the lettering with aluminum tape and have a go with that, first.  We'll see, we'll see...

 The next step is wiring up the motor drive panel and its relays with the cable from the drive proper.  I'll need to cut back a bunch of the cable for service loop, and it's very tempting to insert a connector between electronic mounting panel and the housing with cables.  I like serviceability, even though I am  building this so it won't likely need serviceing again until the day it is scrapped for its iron. :(
(my ghost will haunt the person who does this, until I've driven them mad)

 I probably won't start that today because I have pain-brain.  I would probably cut the red wire instead of the blue wire and blow up the speeding bus. 😂 I need to think about the connector when I can think straight.  Oh shoot, I don't think I own a pair of crimper handles any more (the ones that accept different dies).  I'll have to look.  I think my regular ones (I had two) were in the tool kit that got stolen out of a rental property thirty years ago and I never replaced them because they are expensive.  Grump.

 I guess I'm competent enough to install the power cord, umbilical, and fuse holder into the box.  I might replace the plastic power cord with some nice SO cable. I have to give the original cable a hard look.  It doesn't move, so it's not as if it needs to be more flexible than the basic PVC, and the original power cord doesn't actually seem to have any age defects.  Perhaps I will let sleeping dogs lie.

 ~≈{👁}≈~

Tuesday, August 25, 2020

The Ghost Ship(ment)

 My face (shell) milling cutter has finally arrived...

 

 I may be expecting too much, but so far I am not impressed.

  I haven't done a good cutting test yet because after I installed six inserts, I was shocked at the variations in cutting insert tip height when I measured the thing on the plate, at which point I stopped to figure out what was going on.

 Well, it turns out there are two things going on: 

 Thing One: the inserts themselves vary in dimension by a surprising amount - from .738" to .746":

 At first I assumed this was just shit manufacturing, but when I decoded the entire insert call-out code (APMT1604PDER) I discovered that this is a very low-tolerance insert (that's the 'M'), suitable only for roughing.  These inserts measure within their specification, they're just cheap-ass, low-grade inserts. Well, I can buy others.

 Thing Two: the insert mounting pockets in the shell itself vary in height by several thousandths at least; I haven't completed a formal survey and written down the numbers.  That is NOT normal, and it's not in anybody's specs!  For a shell mill to provide a good surface finish (and they are capable of very good surface finishes, when the inserts are right) the inserts must all be at the same height.

 I've asked the seller for clarification, details, specifications, manufacturer, explanations, etc, but I don't expect to get anything useful because China.

 So, another painful - but not terribly expensive - learning experience.

  And amusingly, it may be possible to even up the cutting tip heights by measuring all the pocket heights and installing the appropriate over- or under-sized insert in each so that the height differences cancel out as much as possible.  Okay, perhaps not so amusing to actually do in practice.

 Gumble.

Sunday, August 16, 2020

where's Kevin Kostner when you need him?

 Regarding that elusive milling cutter which is allegedly on its way to me... it turns out that SpeedPak*, the carrier service used to ship my cutter, hands off their shipments to... the United States Postal Service.

 Now, it really wasn't all that long ago when this would have been happy news indeed because for my entire life, since I was a child in the 1960s until just about two weeks ago, I knew I could rely upon the USPS to do a good job.

 But of course, thanks to our Fearless (Brainless) Leader, the speed and reliability of the US Postal Service is out the window.

 So naturally I doubled down instead of being cautious -- just like our president would!

  Yesterday I ordered, via eBay, a Noga style (Shars, in this case) dial indicator holder, like this one:

 

 This is the second indicator holder I've ever owned, and I bought the first one - even cheaper, a HF PoS, at Charlie's Second-Hand tools for nearly nothing. Before this month, I've gone without, or rather, I've made my own ways and means on the spot as needed. And it's been a pain in the ass, too.

 What makes this style of holder pleasant to use is that the one knob in the middle locks up all three joints.  So you have fastened the magnetic base to something, you can hold the indicator where you want it, use the knob to move the arms to a reasonable position, and then with a twist of that same knob, lock everything up. It's like having a third hand. Another convenience is a fine-adjustment built into the indicator holder, making setup a little easier.

 The other item I picked up is a simple bracket assembly...

 which lets me mount a cheap DRO, or Digital ReadOut, like this one...

 

 to the spindle feed of my Bridgeport mill, like this:

 

...sorta, except the above photos show a method which requires drilling a bunch of holes in the mill, whereas the Shars bracket mounts using the scale screws on the left, and tracks the movement of the quill by picking up that great big round hole in the front of the quill stop. Gotta love this guy's quill feed wheel tho... 

EDIT: I'd quite forgotten, but both these items came from the same seller, who shipped them via FedEx, and they are guaranteed to be delivered by the 20th. Huzzah!

__________________________________________________________________________
* a partnership between eBay.cn and OCL and the default shipping option for sellers in China

Thursday, August 13, 2020

Face Cutter, O Face Cutter - where the fuck art thou, O Face Cutter?

 Mah new milling cutter has vanished into that interstitial Hilbert Space between two parcel carriers:

"Orange Connex" (OCL) in China, and... whoever they handed it off to in the USA after it cleared customs.

 I am used to dealing with the Chinese Postal Service (which isn't too bad, honestly) which hands off to US Postal Service here.  They seem to inter-operate their tracking numbers as well, which is awfully nice.

 This shipment's tracking number works for OCL only, which ceased to be relevant once the shipment entered U.S. Customs. The shipment cleared customs on Aug. 7, and according to OCL's last hand-off message, "Arrived At Destination Hub".  Well, they sorta neglected to mention WHICH "destination hub", ie; WHICH SERVICE it was handed to - the US Postal Service, UPS, DHL, FedEx, Billy-Bob's Bait & Parcel Service, or what.

 I asked the seller whether they knew who OCL hands off to, but they have not yet responded.

 It is not likely to be US Postal Service, because we have a magical service available called Informed Delivery, which sends us, via email, a notification of every single piece of snail-mail they receive which is destined for us, along with a B&W photo of the item, regardless of whether it is personal, commercial, junk mail, advertising and coupon fliers, or a package.

 US Post Informed Delivery doesn't know about any packages coming from China, so presumably it was handed off to one of the commercial services.  I wish I knew which one.

 The seller predicted a delivery time of August 14 - September 9, which I accepted when I bought it, so technically it's not late, and really, I have no reason to doubt it will turn up eventually... I'm just spoiled by the modern world, and I'm bored and eager to get my grubby little mitts (er, well, grubby large mitts) on the thing so I can evaluate and use it.

 UPDATE: jackass seller responded with a bunch of blather about why my package could be late - I never said it was late - and they failed to answer the one and only question I asked.

  So I asked again, and explained why I was asking (which was none of his business, actually) and I held his little baby hand until he stopped crying, but his Feedback-O-Meter is winding downward rapidly.

Friday, August 7, 2020

where to buy used tools in Denver

 Frankly, it's hard to buy used tools without wondering whether they are stolen.

 In Denver, the most common place to dispose of stolen tools is Mile Hi Flea Market.  I personally hate the place and I never go there any more.  I know, with 75% certainty, that the last time I was burglarized and my air compressor was stolen, it was out at the flea market the very next day.  I once bought a large  (and incomplete) Craftsman brand set of taps and dies there, but that's it. And I regret that purchase.

 The second most popular place to "fence" stolen goods is pawn shops.  There are mechanisms in place intended to make pawn shops less attractive as disposal routes, but it still happens. Also, pawn shops usually know what their stock is worth, only rarely do they offer good bargains. Usually their shit is overpriced.  However, I once found an old L.S. Starrett (that's a name brand synonymous with quality) dial caliper in a pawn shop for $10, and it was a funny story...

 I was out with one of my bros, driving down Colfax (the main drag" of Denver, and the longest street in the USA, and home to at least three sketchy business districts in three different parts of the metro area, so a fair amount of pawn shops) and we were talking about this very subject - where to find used tools at affordable prices - and I mentioned pawn shops because at that time I had had one or two bits of good luck and hadn't yet sworn them off. My buddy expressed much skepticism, and as it happened that we were passing a pawn shop that very moment, I abruptly pulled over and suggested we have a look.

And inside we found those calipers, they were missing a locking knob which knocked the price down, but more to the point, they hadn't been priced -- some less-organized pawn shops don't price everything the minute it comes in the door, some will "wheel and deal" -- and it turned out the guy behind the counter didn't really know what dial calipers sold for, and he definitely didn't know that Starrett is one of the desirable brands of machinist's tools.  So I bought them for $10.  The used price should have been $40 - $50 at the time.  My brother was so surprised he was almost disgusted.  It was a fluke, and a moment of luck. It might also have been the last time -- 1989 or so -- that I ever set foot in a pawn shop, because I think they are disgusting, predatory businesses.

Probably the best place to buy used machinist's tools - hell, any used tools - is at estate sales.  Estate sales have lower prices than garage sales, and estate sales advertise what sorts of things make up the majority of the property - if there is a big record collection they will mention that, and if there is a bunch of tools or machinery, they will mention that too.  So there's no need to waste your time traveling to sales all over town - only go to the ones with the stuff you want.  But understand that lots of other experienced tool-users have the same idea, so you have to turn up on the first day of the sale, the moment they open. There will be a short line of other early birds just like you. There is sometimes a little rush for the good stuff on the first day.  You used to find estate sales advertised - along with descriptions of what was for sale - in newspapers, now you find them on dedicated web sites, such as: https://www.estatesales.net/ (an example I just found with a search engine, I know nothing about the site, or even if it's any good)

This morning I am going to run down to a place in Denver called Charlie's 2nd-Hand Tools, a place I've been before, where I've had decent luck.  It's a very low-rent looking, sketchy-looking old building, right in the middle of downtown, in between the shiny sky-scrapers, immense old churches, homeless shelters, and busy-busy big business office buildings.

 I've only been in two or three times, but I found good deals, and the folks running the joint seemed friendly and willing to do a little wheelin'-&-dealin' on prices if you're actually spending some money and not being a jerk. I've spent less than $100 in there so far, and I will take $100 in cash (I can't remember if they take credit cards or not) this morning, in part to limit my spending if I find too many things I want.  I am going with the purpose of finding a convolute abrasive wheel or two (looking for "New Old Stock"), which is where I found my last one at a good price ($10 for something that costs $85 new) but I will also look over all of their indicators, indicator holders, machinist's tools, and machine tool accessories, because there's loads of stuff I still need but don't have.

 A Noga base and arm would be a great find, for example, but I ain't holding my breath. A good "tenths" (.0001 divisions) indicator or dial test indicator would also be very welcome. I'd also consider cutters, tool holders, anything at all that I need and don't have if it's cheap enough.  Ooh, they just opened, and I have to work today too, so I'd better run.  I'll report back on anything I find.

Thursday, August 6, 2020

is it the arbor, or the mill?

The arbor for My First Shell Mill (new from Fisher-Price!) arrived today, and it seems to be a thing of beauty and a joy forever:
But experience has taught me not to be a trusting soul, so I thought I'd put the thing in the mill and put an indicator on it to check the runout.

No doubt those more experienced than I are already chuckling at my expense.

 I got a real shock when the indicator showed me a solid .001" TIR (± .0005) of runout, measured barely an inch below the R8 spindle nose!  I would have thought that would be unlikely given the precision of modern automated grinding machines, and given the ease of maintaining good dimensions and geometry on a cylindrical feature.

Indicating the inside taper of the spindle was going to require me to bend over more than I wanted to, so I tabled that for the moment and took the arbor over to the surface plate.

I set up the arbor on two vee blocks...

Oh bother; the two features I'll be rotating on are two different diameters... I need to shim up one of the vee blocks... well, paper is very consistent on its thickness... our printer paper is... hey, that's convenient, it's exactly .005 thick and I need one vee .120 higher than the other... so I need 24 sheets of this particular flavor of printer paper. Sweet, done.

Ahem. I set up the arbor on two vee blocks, fastened an indicator to some 1-2-3 blocks as an improvised height gauge, and measured the by-god-actual runout of the arbor... which was zero.

We now scowl at Mr. Bridgeport in a very disapproving manner.

Indicator goes onto the (rather rough and beat-up) outside nose of the spindle.
One thou of runout.
Hmph.
Indicator goes inside spindle to measure actual taper that touches arbors and collets.
One thou of runout.
>> Outrage face <<

I stomps myself into the house (no computer in the shop, yet, still, some day, need to find the space) and I searches YouTube and DDG and Google and I got learnt!

What I found surprised me: there is a lot more spindle runout tolerated and expected from general purpose mill spindle bearings than I had expected.

In all likelihood, the spindle on this machine had a max runout of .0005 when it was new.

Everyone agrees that more than .004 or .005 is unacceptable and time to replace or rebuild the spindle.

.001 now is actually quite good for this machine.

Well, if the spindle is free to flop around so much, how is this machine and others like it holding tolerances as tight as .001?

A moment's reflection, and something I had never thought of before this hour, gave me the answer.  It took me ten minutes of searching on the internet before I knew I was right, though. Yay, good intuition... it's the machining reaction forces!

The moment that cutter touches work, quite strong forces - ranging from ounces to hundreds of pounds - pushes against the spindle bearings, taking all the slack out of all the moving surfaces, and so long as that cutting force remains fairly constant, no sloppy movement should occur.

And then one of those cartoon light bulbs went on over my head as I realized: I never could get good surface finishes the few times I tried non-helical cutters... well, helical cutters tend to keep the cutting force constant if the cut is over the side face of an end mill.

Learn something new every day.

Side note: if I'm still learning, then I am still "swimming upstream", therefore I am not a complete loss to society, yet. Just remember though: the only fish swimming with the current... are dead.

Sadly, it will be another week at least - if I can trust the tracking information from China's Post, which is roughly as accurate as British Rail timetables in the 1980s - before I receive the shell mill itself, and am able to evaluate the real, fundamental Quality of my "bargain".